120mm to in 3d models
2618367 3d models found related to 120mm to in.thingiverse
This screw together spool will hold the small 120mm spools to fit into the 200mm Bambu AMS
thingiverse
i actually like these better than the adjustable ones for suspension and use the adjustable ones for steering again print on a raft and best to use a sanding block to sand down the raft as a dremel tends to melt the ball and outside together a little...
thingiverse
This converts between a 120mm fan such as a Noctua and a 5" duct to vent outside.
thingiverse
A 200mm to 120mm fan adapter. Update 12/8/17 I have noticed some issues when this printed. my print separated. i am trying to work on a fix for this now. ...If anyone has come up with any ideas that would be awesome.
thingiverse
Needed a 120mm to 80mm elbow duct to fit inside 120x120x120mm build space. Printing to test now. Thanks @sheriftahers ! If you like my things please consider donating via paypal : jaraddavey@tpg.com.au or use the 'tip' feature when...
thingiverse
fan adapter to mount a 120mm fan in a 140mm grid. ... example 120mm fan: https://amzn.to/2V8V0v5 example 140mm fan: https://amzn.to/2QkZyzX hole distance (120mm fan): 105mm hole distance (140mm fan): 125mm
thingiverse
I made this to adapt a 140mm fan in place of a 120mm fan in a desktop evaporative cooler.
thingiverse
120mm fan to 75mm x 2. ... Used in my boat to distribute heat in the boat. Used in combination with my other design 75mm to 120mm fan. ... I would NOT recommend printing in other materials than ABS or materials with similar heat carateristics.
thingiverse
Remixed to act as a gasket around a 120mm fan when the fan is installed in a location that has both 120mm and 140mm mount points. The gasket covers up the extra open mesh around the smaller fan. Should work on any case who's fan holes have both...
thingiverse
This zero-thickness adapter allows you to install 120mm fan into 140mm place.
thingiverse
Adapter manifold to use standard 120MM fans on EMC power supplies that use 40MM blowers.
thingiverse
... I printed this for my CPU cooler. Make sure you have enough clearance, it might collide with high ram sticks. This 3D model is printed in two parts, the 120mm part has a ring and the 92mm part has a cone that both needs to be oriented upwards.
thingiverse
Adpater desinged to reduce a 120mm outlet to a 100mm flange to connect to a tubing. Usefull to adapt new air extractor fans to old tubes. Recommended to print in PETG as PLA can be too brittle for this use. Enjoy! ...
thingiverse
Adapter for using 120mm PC fans with 140mm fan mounting holes. ... The standard one ca nbe used to mount with standard PC fan screws. The short one is to mount 120mm fans to 140mm radiator.
thingiverse
... but serve more like placeholders that can be drilled out to your needs. Please note that my print stopped prematurely due to filament shortage, and as it's not supercritical I left it as it is and will glue it in place to achieve an airtight seal.
thingiverse
Connects any 120mm computer fan to 75mm duct. Has a flange on one side and a tube on the other. ...
cults3d
I designed the adapter in Imperial measurements, so make sure to double check your settings before printing a very small adapter. EDIT: I have redesigned it slightly to fit the original metric units. ...It should be a perfect fit now for a traditional...
thingiverse
I designed the adapter in Imperial measurements, so make sure to double check your settings before printing a very small adapter. EDIT: I have redesigned it slightly to fit the original metric units. ...It should be a perfect fit now for a traditional...
thingiverse
This is an adapter to mount a 92MM fan to a 120MM computer case or bracket. I needed this to reuse a good fan in a new PC case so figured I would share. ...I couldn't find one from someone else so made my own.
thingiverse
A hose adopter for 150mm hose to wall mounted 120mm outlet. The smaller ring is 195mm, so this is a loose fit. This work well in my case because the hose will pressurise and push towards the outlet. ...I can scale a 198mm version if anyone need.
thingiverse
I use a 120mm fan hooked up to a lipo battery to cool myself. This is a mount to enable me to connect the fan to the gopro connecting system so I can orientate it correctly. It's threaded to accept M4 bolts. Printed using PLA and default settings....