135 degree bracket 3d models

Just a small clip I designed to hook up a light switch onto my printer spool's base. It's got a sharp turn up and off to the side with a triangular stabilizer. Installation Guide Shrink to 0.2...

No supports needed

fits 1.25x1.5" aluminum tubing

3/16 Holes for rivets. ...Made of .063 aluminum.

First real usable STL file I made using Solidworks,

This is just JinwooYoo's original design, except with four holes instead of six, making it narrower.

This is just JinwooYoo's original design, except with four holes instead of six, making it narrower. ... Category: Replacement Parts

Extra Heavy Duty 90 Degree Bracket 2-3/4" x 1"

High-strength 90-degree corner bracket measures 52 x 25 millimeters.

A double 45 degree bracket for 2020 aluminium profiles, based on the 45 degree 2020 bracket of StarrEngineer (@StarrEngineer_234359) , to attach two angled profiles at the same height on a single straight profile.

I reside in Arizona and the primary bracket began warping or "melted" down, so I incorporated a 45-degree stabilizer to maintain structural integrity.

... Micro Servo bracket. ...Perfect for mounting servos in situations without pre-determined spots. Use wood screws to screw it in. Alternative Version Here: https://cults3d.com/en/3d-model/tool/rc-micro-9-gram-90-degree-servo-bracket-holes-on-bottom

... Strip. ...This innovative mounting bracket was specifically designed to securely fasten 5630 LED rigid strips at a 45-degree angle, perfect for illuminating inside IKEA Lack enclosures. ...The strip's dimensions are precisely 12mm wide and 1mm thick.

... Degree Micro Servo bracket. ...Perfect for mounting servos in situations without pre-determined spots. Use wood screws to screw it in. Alternative Version Here: https://cults3d.com/en/3d-model/tool/rc-micro-9-gram-90-degree-servo-bracket-holes-on-top

The 3D model showcases a high-polygon representation of the Bohle 90-degree Glass-to-Glass Fixed Bracket, which is specifically designed for use in architectural hardware applications involving corner glass railings.

I designed a custom 45-degree bowden bracket for my Hypercube printer, specifically to mount my BMG extruder and its motor at the top of the 2020 aluminum frame. This design allows me to reduce the length of the bowden tube. ...The bracket attaches...

Human: 45-degree angle pole brackets available in right and left parts. Perfect solution if your 3D printer is installed in a corner like mine. Engineered to work seamlessly with the gypsum anchors shown in the picture. The pole features a diameter...

To install 12mm LEDs at a 45-degree angle, you'll need these components: an Adafruit LED Strip Controller (available for $17 on eBay), an Arduino Nano ($8 on eBay), 25 3D printed LED mounting brackets per LED, and 26 inches of 3M Velcro tape cut into...

The aluminum channel is designed to snap into this bracket, directing the lights at a precise 45-degree angle relative to the mounting surface. *** I updated this model on October 2, 2017 *** After six months of rigorous testing, one of my LED strip...

The aluminum channel snaps effortlessly into this bracket, directing the lights at a precise 45-degree angle relative to the mounting surface. I made significant improvements to this design on October 2, 2017. After six months of thorough testing, I...

I created this 90 degree bracket to hold "Ricoy 3/4" Round LED Underbody Rock Front Rear Side Marker Indicators Light Waterproof 12V for Car Truck Trailler ATV Boat Light, Pack of 10 (white)" (purchased from Amazon). The holes should line up with a...

This is bit of an experiment - rotating the extruder by 90 degrees in 1 axis, 45 degrees a 2nd axis, and then shifting it 70mm or so in towards the center of the bed. Makes it easier to feed filament from spools that are sitting to the right of...

This is bit of an experiment - rotating the extruder by 90 degrees in 1 axis, 45 degrees a 2nd axis, and then shifting it 70mm or so in towards the center of the bed. Makes it easier to feed filament from spools that are sitting to the right of the...

There are several variants of this bracket on Thingiverse, but they all annoyed me as they don't allow "full" rotation of the camera around the mount. I made a new variant that thins out so the camera can rotate 270 degrees. You'll need to print...

Used for my stairs on a 45 degree ceiling

They are pretty effective while being unobtrusive. Check out these other things for IKEA Lack table... Stacking leg couplers: https://www.thingiverse.com/thing:3488697 Table leg levelers: https://www.thingiverse.com/thing:3495732 Print...

Ultra-durable 90-degree corner connector, measuring 36 millimeters by 25 millimeters, engineered for heavy-duty applications.

Engineered with precise mounting holes that easily accept standard 6mm bolts, this bracket offers secure installation. Moreover, two sturdy 8mm wide lugs are strategically designed to keep the entire assembly square to the aluminum extrusion. ...To...

This is an adaptable OpenSCAD endeavor that allows you to tailor various dimensions such as switch width, bracket width, and hole diameter.

I wanted the brackets to be very strong, so I put an infill of 0.5. The print took about 6 hours per bracket. It might work with a 0.25 infill, but I didn't want to take any chances. ...No support material necessary.