14 mm gauge 3d models

This was made so I could make things with LEDs. This guide may help with all different LED sizes that are out there. This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/0x17srDL17i

A very simple radius measurement gauge that I whipped up when I needed to measure something in a pinch. Measurements for 8mm, 10mm, 12mm, and 14mm radii (radiuses?). ...Prints in just a few minutes.

standard sheet size 2000 mm x 4000mm .14 Gauge Steel Sheet

... with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=69655 Instructions Using the following options: ToolOptions = 2 Tool_Length = 10 message = 14 mm kerf = 0.3 Nut_Size = 14 Font = write/Letters.dxf DualExtrusion = Extruder1

... http://www.thingiverse.com/thing:667378 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=667378 Instructions Using the following options: height = 150 handleDiameter = 12 nut = 14 handleHeight = 60 shaftDiameter = 6

14 mm combination wrench

There are 4 versions: Raised tic marks, Raised Tick mark with mm number, Recessed tic marks, Recessed Tick mark with mm number. the gauges start at 1mm and increment up by .5mm. 1mm-25.5mm I made this for measuring the gaps in a table saw guide...

just a simple gauge pod nothing to fancy

this is a sample of an gauge block with it's materials to calibrating and measuring.

Marking gauge with 150mm body. ... Should be printed upside down with no support material.

... 0,1 cm to 10 cm in 0,1 cm steps. The 0 cm-mark's purpose is to check the alignment. Also I added a blank version of the gauge as .FCStd (use FreeCAD) so you can insert your name instead of the "10 cm". ... _____ Print and use at your own risk.

Mini Whistle printed with a diameter of 14 mm. The diameter can be reduced to 9.4 mm. However, it only works without reduction. ...My mini whistle is similar to http://www.thingiverse.com/thing:328058 Print Settings Printer: BQ...

Nema 14 12 V 0.4 A per phase stepper motor.

... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=44815 Instructions Using the following options: $fn = 50 type = 1 cursor = 100 diameter = 14 edges = 1 groove = 1 weight = 11 margin = 0.1

... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=44815 Instructions Using the following options: type = 1 weight = 11 margin = 0.1 groove = 1 $fn = 50 diameter = 14 edges = 1 cursor = 100

... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=44815 Instructions Using the following options: $fn = 50 edges = 1 groove = 1 diameter = 14 margin = 0.1 type = 1 cursor = 100 weight = 10

... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=44815 Instructions Using the following options: weight = 11 cursor = 100 margin = 0.1 $fn = 50 diameter = 14 groove = 1 type = 0 edges = 1

https://www.paypal.com/paypalme/moorhuhn86?locale.x=de_DE Abstandslehre mm Distance gauge mm, Herringbone teaching mm

52 MM SINGLE GAUGE POD

... from 0.5mm to 10.5mm. Measurements include a concave and a convex part. English: Here is a round meter to measure the edges when you want to make a design. The gauge ranges from 0.5mm to 10.5mm Measurements include a concave and a convex part.

3D model of a Dashboard gauge pod for 52 mm gauge.

Test gauge with 0.2 mm spacing between the walls.

Fillet Gauge 28 - 35 mm Could not find gauge in this size, so I made it. ... I will be glad, if helpful.

Pocket 14 mm wrench

Three versions are available: 2-9 mm, 2-5 mm, 6-9 mm Print settings: basically whatever you like, but first layer must be small enough for the 0.3 mm bevel (=0.2 mm or lower for first and last layer). ... Rafts: No Supports: No Resolution: ...

Compact gauge for outer and inner radius 1-20 mm.Printed with Prusament PETG, no supports.Layer hight 0,15 mm (first layer 0,20 mm).You need two M5x30 screws and two M5 lock nuts for assembly.Inspired by https://www.thingiverse.com/thing:5205494,...

Large clip 14 * 90 mm.

A pritnable gauge for threadless headsets. ... Contains following sizes *34 *41 *44 *49 Both for ZS, EC and IS types

This is my first 3D printed thing - needed a thin 14 mm wrench to unscrew a nut in a hindered location.

Pocket 14 mm wrench Category: Hand Tools