140 mm to in 3d models
2759278 3d models found related to 140 mm to in.thingiverse
Simple design to use an 140mm fan as a blower for a 90mm air duct. ...There is an electronic box on top for a two position switch, micro usb port and lipo (boost) circuit.
thingiverse
140 to 120 mm fan adapter offset. ...I used it to attach 120mm fans to my 280 aio on the top of the case, so the fans can clear the ram sticks
thingiverse
This is exactly as the name suggests. ... Print it with larger plate down. Use supports under upper corners. I used IdeaMaker to put supports manually.
thingiverse
I basically modified the stock 140 to 120 mm fan adapter to make it super short in order to mount the radiator for my video card higher up in my chassis, alleviating a bend in the hoses that's pretty sharp. I have a Corsair H80i GT mounted in the top...
thingiverse
This shroud adapter is to be attached to to the fan on the exhaust side so a 120mm duct can be attached for routing the hot air away. ... Use Temperature resistant filament like ABS or ASA as the exhaust air of the Miner can be quite hot (hot enough to...
thingiverse
As a request, this part is a "Blanking Plate" for a 140mm (computer case) fan intake, to aid in case pressure for better cooling and air flow, as well as reduction in noise and dust ingress. Informational video can be viewed on SBS Extensions YouTube...
grabcad
This file is an accurate model of a 140 mm diameter disc. ...You may have to change the location of the assembly holes in order to adapt it to your own file.
thingiverse
Yet another quick and simple fan grill for 140 mm computer fans. ... This is not for protecting fingers (obviously) but for supporting fan filter / mesh which does not have internal support structures and have to be mounted on intake side.
thingiverse
I needed a connector from a 120 mm fan to a 4 in vent hose. I used this for my greenhouse blast gate air control as well as my Martha mushroom fruiting tent. Hole pattern bolts directly to a 120 mm fan. You need to use stainless bolts in the...
thingiverse
Based on http://www.thingiverse.com/thing:143424 by bold. ...I have modified the height, in order to be used by filament rolls of 80 mm of radio.
prusaprinters
The filter itself is made by infil, so set top and bottom thickness to zero. I have added a .3mf from cura with infil blockers with 100% infil to make the corners more sturdy (the top of the two filtes). Print Settings Printer Brand: Creality...
thingiverse
https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...
thingiverse
... size and spacing as per 140mm fan standard. The filter itself is made by infil, so set top and bottom thickness to zero. I have added a .3mf from cura with infil blockers with 100% infil to make the corners more sturdy (the top of the two filtes).
thingiverse
I dust inside my computer pretty regularly and don't want to compromise airflow, so honeycomb at 40% works pretty well with a 4mm nozzle. Hotsnotting refrigerator magnets on the corners worked perfectly. Includes 10mm and 25mm squares for testing...
thingiverse
I designed this for my SFF pc my 280mm AIO I cannot fit 120mm fans and because I had limited space I couldn't buy one as all were too thick and too expensive. These can take 140mm fans and have them fit into 120mm sockets or have 120mm fans fit...
thingiverse
Created to go with the **CR10 Portable** because I had plenty of 120mm fans laying around, but no 140mm fans.
grabcad
Fan, Grill, Shelby, Cobra 140, mm, 14mm, mustang, Zerous, Zeromod, ModdingZ, Fans, Mod, 3Dprint,
myminifactory
Simple PCB Holder with size 140 * 220 mm and height 15 mm, slot width 2 mm. ...If needed - i can send you original solidworks 2016 file.
thingiverse
... silent version that does not interfere with the airflow of the fan you mount. ...Can be printed without support. 45° overhang. Base, Box and Bars are identical for 140 and 120 mm versions. ... Both assemblys can be printed on prusa i3 in one session.
thingiverse
Ceci et un support de ventilateur de 140 mm pour etre mis dans un emplacement d'aspiration de 70 mm d'une VMC. ...Cela permets de diminuer rapidement d'humidité dans l'air.
thingiverse
... help to make it more usable. I also hate limitations so I figured I would make this spacer in a way that would allow customization to whatever mounts you may wish to use it with. Have a great day, enjoy, and may all your prints be flawless. ...=D