15 22 charging handle 3d models
318591 3d models found related to 15 22 charging handle.
thingiverse
Replacement piece for Smith and Wesson's M&P 15-22 charging handle release button.
thingiverse
New design V2 more realistic. ... The Design works great with Smith & Wesson MP 15-22,and only use two little 2.3mm diameter spring.
cults3d
Charging handle for Ruger 22/45 I printed in petg. ...pla was to brittle to put on without breaking it
thingiverse
Charging handle for Ruger 22/45 I printed in petg. ...pla was to brittle to put on without breaking it
cults3d
CMMG style charging handle insert for ar15 to prevent ammo from getting stuck inside bcg and stove piping.
thingiverse
Charging Handle for Ruger 22/45 MKIV May work with MKIII but only have tested it with the above. Your printer has to be really dialed in because the tolerances are tight. Print solid for best results. Need a 3-48 cap screw to assemble. ...STEP file...
thingiverse
2 piece charging handle one small spring 1m4 screw with nut
cults3d
Perfectly matches the mp15.22 semi auto rifle Printed in positions as shown with support attached.
grabcad
This part is designed to provide a left side charging handle for the Ruger 10/22 very popular rifle. It allows right handed people to perform tactical reloads with their right hand never leaving the pisto grip with the finger on the trigger in...
thingiverse
This part is designed to provide a left side charging handle for the Ruger 10/22 very popular rifle. It allows right handed people to perform tactical reloads with their right hand never leaving the pisto grip with the finger on the trigger in...
thingiverse
This part is designed to provide a left side charging handle for the Ruger 10/22 very popular rifle. It allows right handed people to perform tactical reloads with their right hand never leaving the pisto grip with the finger on the trigger in...
cults3d
different charging handle tab for m16s, ar-15s etc airsoft aegs
thingiverse
AR-15 and M16 milspec charging handle, modified to use a standard pen spring and a paperclip at the pin. This works in an AR-15 and actually stood up to being racked a couple dozen times, when printed in PLA+. It could probably be actually usable in...
thingiverse
Designed to clear protrusive optics like red dot reflex and scopes. ...I kept cutting my finger on battery cap knurling on reflex optic so I modeled this.
thingiverse
These are extended charging handles I created for my HTA 90/22 kit. I'm sure they could have other applications. V2 works flawlessly. V5 had to but drilled a bit it also has a bit more ABS where the screw goes though and has ticker side walls. Print...
thingiverse
Just added the M&P logo to chevyfried's lid for my 15-22 Fits the box that I remixed it from
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=44850 Instructions Using the following options: cone2_max = 22.3 barb_skew_ratio = 0.15 cone1_wall = 2 cone2_min = 22 barb_flatness_ratio = 2 cone2_height = 22 check_guts = 0 cone2_wall = 3.5...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=44850 Instructions Using the following options: cone2_max = 22 check_guts = 0 barb_skew_ratio = 0.15 cone2_min = 22.37 cone2_height = 21 join_height = 6 barb_spacing_ratio = 5...
grabcad
I poached the Upper from a GrabCad user. This is a mock up of something I intend to build for my 450 bushmaster. Often times its hard to get under a low scope. ...I would rather add these parts which are easy to remove compared to machining my upper.