15w led driver 3d models
92683 3d models found related to 15w led driver.grabcad
LED power supply SNAPPY Optoelectronics SNP15-12VL 12V DC 1.25A 15W
grabcad
Constant Current LED Driver Powers four 1W or two 3W LED's. High efficency Switch Mode operation. Driven from 6-14v AC or 9-18v DC source. 350mA or 700mA configurations. ... For detailed build instructions and parts list go to:...
grabcad
A selectable led flash light driver. ... Part: http://illuminationsupply.com/8xamc7135-28a-selectable-mode-driver-p-45.html
thingiverse
Mini LED driver holder. Driver used to control 3d printer lights. ... Driver from http://goo.gl/Onm0Nk used with lights http://www.thingiverse.com/thing:856626
thingiverse
A simple case to go over my Picobuck LED driver and protect the contacts. Note that it has ventilation holes, but they might not allow enough cooling, depending on how you use the driver. ...Also, I only used one output of the Picobuck, so I only made...
thingiverse
I like these tiny LED drivers on Ebay, but the box was a little bit too big. So I designed a smaller box. ... Printed in PETG 235 nozzle, 70 bed, 0.2 layer, 25% infill
cults3d
I like these tiny LED drivers on Ebay, but the box was a little bit too big. So I designed a smaller box. ... Printed in PETG 235 nozzle, 70 bed, 0.2 layer, 25% infill
thingiverse
This is designed for a standard 12v LED driver module and has suitable outlets for power and two separate lights and two switches on the top plate. ...A link to the required...
thingiverse
Based on the driver for ME 2019 LED Strip Light Kit, New Acrylic Back Tape, 16.4ft Water-Resistant Flexible Multicolor 5050 RGB Lighting; however, it should work for other products with the same driver. See installation details below. Requires a...
pinshape
If the range does not work for you because the LED is already at max level when the potentiometer shaft is only at 50%, than you can replace this resistor with a 50K potentiometer to “fine tune” it. Than you need a case to hold the parts...
thingiverse
If you have your LED’s and the right resistor (I have talked about in https://www.thingiverse.com/thing:2660485) you can make this driver case. I included a schematic for connecting the parts. Because it’s so simple, I didn’t even make a PCB, but...
myminifactory
This is a follow up part for the adjustable LED base: https://www.myminifactory.com/object/50232 If you have your LED’s and the right resistor (I have talked about in https://www.myminifactory.com/object/50232) you can make this driver case. I...
cults3d
If you have your LED’s and the right resistor (I have talked about in https://cults3d.com/en/3d-model/tool/adjustable-led-base) you can make this driver case. I included a schematic for connecting the parts. Because it’s so simple, I didn’t even make...
thingiverse
Ok guys, the LED driver of the chinese LED ceiling lamp I bought was way too big for the small circuit board, and I needed space to fit in additional stuff (Wifi control module, etc.), so I set out to design & build a smaller one. So there you go,...
prusaprinters
Do not print and install this model if you don't know what you're doing!!!This model is a replacement enclosure for a 24V LED driver with passive cooling. ...You can mount the power supply to the enclosure with some M4 bolts and...
grabcad
Circuit powerd by mains voltage, with a small control circuit as LED dimmer. ...Light intensity is controled with the potentiometer.
grabcad
Current flows from thesupply through one pair of LEDs, through the regulator, through the other pair of LEDs, and back to the battery. The capacitor filters out noise on the power supply lines. The LED pairs must be matched so that the current...