16 fan blade replacement 3d models

Fan blade design

Xiaomi Fan blade replacement

suddenly i broke my 50mm fan blade and i have to replace it... but i can't find a suitable size for it... ...ID=29,5 ; OD=47,5 ; 7 large blade...

suddenly i broke my 50mm fan blade and i have to replace it... but i can't find a suitable size for it... ...ID=29,5 ; OD=47,5 ; 7 large blade...

The original fan blade replacement was a bit cumbersome to me, so I modified the blade assembly in order to have a complete replacement of the blade assembly, including the axle support. From the old fan blade assembly I keep the magnet and the axle...

Here is an replacement fan blade for an 50mm fan. ... It just fit it in but if you want you can use a little bit of glue to fix it.

replacement fan blade assembly for a 92mm fan. one of the welders at work was missing 2 fan blades so i knocked this up to get it going again. blows a heap of air. may need to scale it to suit your application though. just snap off the remaining...

fan blade for 40mm fan, simple to fix if you havent got time to wait for another unit to be delivered.

... ID of the fan ring is 46.8mm with 84mm fan blade diameter.Print SettingsPrinter: wanhao d4sRafts: YesSupports: NoResolution: .2Notes: printed in ABS using 0 infill 4 top and bottom layers and 10 lines of raft to help keep the blade tips down.

I had a blade break off the main fan, and I didn't feel like spending $7+ to get a new fan. This may actually have been better due to the noise reduction. Customized version of https://www.thingiverse.com/thing:2536887 Created with...

This is meant to be a patch job until you can get the fan replaced. You can see it in the preview of the model above. Print this out, Disassemble the old fan(Might not need to, but that's what I did). Cut the old fins off, add a little glue press...

This is meant to be a patch job until you can get the fan replaced. You can see it in the preview of the model above. Print this out, Disassemble the old fan(Might not need to, but that's what I did). Cut the old fins off, add a little glue press...

Plastic Blade

Replacement fan blades for one of the 40x40mm type fan. ...Fits to Anet A8 3D printer for fillament feeder cooler fan.

We couldn't find a replacement fan blade for my 2007 Yamaha Phazer Snowmobile and decided to design one on TinkerCAD

40mm Ender-3 Fan Replacement / Sleeve I accidentally broke a couple of fan blades while tinkering on my hot end. So I decided to print an easy diy replacement sleeve / fan blade set. I printed the part in vase mode, but should also work with...

Replacement fan blade for a [Vornado 630 Medium Air Circulator](https://www.vornado.com/shop/circulators-fans/630-medium-air-circulator). The blade and hub measurements match the original, but I kind of eyeballed the fan blade angle and it works...

-Replacement for the standard RV vent fan blade. -Be careful, this could be dangerous in application and cause personal injury. I recommend covering with a screen to prevent injury. 9/29/13 UPDATE: Had a chance to install. I would recommend making...

Customizable blade replacement for repairing centrifugal fans with broken blades on laptops, 3D printers, and anything else. How to determine sizing: * Cut all the blades off of the damaged fan leaving short (~1mm) and evenly sized stubs. Using...

Customizable blade replacement for repairing centrifugal fans with broken blades on laptops, 3D printers, and anything else.How to determine sizing:Cut all the blades off of the damaged fan leaving short (~1mm) and evenly sized stubs. Using flush...

This is a replacement fan hub and fan assembly for a 30mm fan I had which broke apart. You'll need a printer which can print very fine features for this print to work, it was very difficult getting a usable (but ugly) print from either of my FDM...

We lost the screw cap for our fan so printed this as a replacement and screws right on. Couldn't find a file anywhere on the internet so thought I would upload this and hopefully it helps someone else out. Feel free to remix, it's a little crude...

90mm Replacement Tower Fan Blade Section

I accidentally snapped two of the blades off my ender 3 heatsink cooling fan. ...This replacement fan blade got my printer up and running again until I could get a new fan.

My Fan Blade Broke while doing some maintenance for my Replicator Dual Extruder Which fit with replicator and replicator 2x and replicator dual and many other printer it is kind of not easy replacing it but any way i uploaded the files for who want...

I accidentally broke some blades of my 40mm fan. So i created these replacement blades to fix it. The 9 blade version has curved blades. On my fan the 6 blade version creates a better airflow. Inner diameter is 25mm, it is designed to press fit onto...

This is a replacement fan hub and fan assembly for a 80mm fan I had which snapped off at the shaft. A printer which can print fine features is recommended, I was able to get a decent print on my Ender 3 with a 0.4mm nozzle and a 0.1mm layer...

35mm replacement fan blade for Hobbywing Max6 and Arrma 35mm fans I made this a complete replacement vs a slide on design because I wanted the maximum amount of blade. A few millimeters matter when you need maximum cooling for something like the Max6...

This is compatible with the Noctua A12-25 A12 fan (if you remove the fan blade off the fan). Should press to fit on the fan motor hub. Design by NatureHacker @ NatureHacker.org Future: Will improve Solidworks tree organization. May improve...

Are you as intelligent as I am and like to stick Q-Tips into running fans of your hotend? Well sigh no more! ...This will have you up and running in no time again!