16mm reel 3d models
19547 3d models found related to 16mm reel.thingiverse
This is just a simple 16mm projector take-up reel, using laser cut acrylic (1/8") and a 3D printed center piece. Assembled with your choice of 8 M3 screws, 6mm works well. The reel can hold aproximately 500 ft, I just designed it to hold some film...
thingiverse
The reel is relatively easy to load if you set it on the lower tank and slowly crank the film on, but I recommend practicing in daylight and then in dark with a test role a few times to get the feel of it and recognize when it isn't loading...
thingiverse
Scaled to fit a Stainless Steel Nikor Developing Tank. ... Push load type reel. ... Helps to taper film of feed end OTHER SIZES ARE HERE MINOX - https://www.thingiverse.com/thing:4831142 17.5MM HIT - https://www.thingiverse.com/thing:4831135
prusaprinters
Scaled to fit a Stainless Steel Nikor Developing Tank. Push load type reel. Helps to taper film of feed end OTHER SIZES ARE HERE MINOX - https://www.thingiverse.com/thing:4831142 17.5MM HIT - https://www.thingiverse.com/thing:4831135 Print Settings...
cults3d
This is a generator for film reels for Super8, standard 8mm, and 16mm film reels. I also included a set of 3 standard sizes for each version as STL files. The reels have 3 insert for the films in the core to make it easy to fit the film onto the...
thingiverse
This is a generator for film reels for Super8, standard 8mm, and 16mm film reels. I also included a set of 3 standard sizes for each version as STL files. The reels have 3 insert for the films in the core to make it easy to fit the film onto the...
thingiverse
Film spool of 29,5 cm (max. printbed size). After printing the 3 elements, it can be clicked together without using glue. Monoprice MP10 printer model (not selectabele in printer model). ...
thingiverse
This is a spool for developing 16mm film from cameras such as the Minolta 16 series. ...You can load 3 rolls of film per layer, and a standard Paterson tank can accommodate a reel with four layers.
thingiverse
Customized version of https://www.thingiverse.com/thing:1689102 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1689102
thingiverse
Customized version of https://www.thingiverse.com/thing:1689102 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1689102
thingiverse
Customized version of https://www.thingiverse.com/thing:1689102 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1689102
thingiverse
Customized version of https://www.thingiverse.com/thing:1689102 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1689102
thingiverse
Customized version of https://www.thingiverse.com/thing:1689102 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1689102
thingiverse
Customized version of https://www.thingiverse.com/thing:1689102 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1689102
grabcad
The centre hub will be wider then the 8mm reel. ...One side of the core can be flush with the reel, the other side can stick out.
thingiverse
This take-up reel was designed by Curt Fielder. ... The bottom reel will need to be rotated 180 degrees for printing.
thingiverse
Created this little reel as a repacement for a broken one. Can be helpfull for someone else. Print 2 pcs of the "disc" and one "core". ... Put together by pushing the pins of the disc into the holes of the "core".
thingiverse
The other day, I ran my car over the extended end of my automatic hose reel, shattering the stopping ball. So I made a new one. This object fits quite tight on a 16mm garden hose. Print 2 of these, and you're set ! This thing was made with...
youmagine
I took the basic dimensions and created a simple two part model of the correct 16mm film reel from Kodak... clicked print... clicked the two parts together 38 minutes later, just after finishing my evening food and HAY HOOO LETS GOOO.... was back...
prusaprinters
<p>I shoot and home-develop a lot of different film formats, and I found myself unsatisfied with the “solutions” I had for developing 110 film. I made a version specifically for my Jobo dev tanks, and got a lot of feedback from people asking Paterson...
thingiverse
Insert your reels and axles into the slot then close the retainer clips so they don't jump out and roll away. ...The film edges should slide into the focal clips, which will hold your film flat and at a consistent height without touching the...
cults3d
Insert your reels and axles into the slot then close the retainer clips so they don't jump out and roll away. ...The film edges should slide into the focal clips, which will hold your film flat and at a consistent height without touching the...
thingiverse
Quick change / replace clip on SMD reel holder for CHMT pick and place machines (Tested on CHMT36) This was designed since CHMT Entry level P&P machines have very limited amount of reels (only 22x 8mm tapes with different values). 1) Reels from the...
thingiverse
Allows you to use one 16mm reel on a set of Neumade rewinds.