18650 BATTERY CASE
18650 BATTERY CASE
thingiverse

storing case 2 18650.

18650 Battery Case
18650 Battery Case
thingiverse

This is a case for two 18650 batteries.

18650 battery case
18650 battery case
thingiverse

This case is 18650 León. ...http://arbu00.blogspot.tw/

18650 Battery Case
18650 Battery Case
thingiverse

I like the venal 18650 cases.Because this make my own design) With this case you can store 4x 18650.

18650 Battery Case
18650 Battery Case
thingiverse

We have a simple case 18650. ...The top slides just above the ground.

Magnetic 18650 Battery Case
thingiverse

box magnetic battery cover, the holes are made approximately 3 mm x 1 mm magnets. ...Case fits 3 18650

18650 Battery Case
18650 Battery Case
thingiverse

Case 18650 with two lid.Print Adjust sliding Sprinter Brand: CR-10S Rafts: Creality unsupported printer Matter: yes Resolution: 0.2 Filling: 30%

18650 battery case
18650 battery case
thingiverse

NEW BODY RE EDITED 9-17-17SCALE RISEN UP BAD cover installation or you have battery case for my vaporizer Issue 18650 / flashlight.

Triple 18650 Battery Case
myminifactory

This is a case of triple 18650 6 mm x 3 mm magnet is used for the cover. ...All I use have built N50, you can see pretty cheap online.

18500 + 18650 battery case
thingiverse

to bring the case 2 18650 2 18500 batteries, FPV, batteries for my transmitter X-lite and a set of parts for my Fatshark goggles.use 18650 2 6 mm diameter x 6 mm magnet for locking system used. UPDATE 16/01 / 19 - changed files 18xxx text reads...

18650 Battery Case
18650 Battery Case
thingiverse

Hi, this is a case of 2 x 18650 batteries. It's a remix of the big box Philhawtin battery climbed 105% and split into two files! ...how to use it and enjoy it without supporti face printed printing it in PLA, first 2 times open tight-fitting, blink a...

18650 Battery Case
18650 Battery Case
thingiverse

battery box for one battery 18650. did not know how the other cases I've found here, so do better. Beautiful, large cap, thick grip. The long thread makes it possible to fit protected batteries that could be longer than 65 mm. The bulk grip also...

18650 Battery Case
18650 Battery Case
thingiverse

It is a house of two batteries designed for 18650 battery. I use this to carry spare batteries for my vaporizer / Mod mechanical pen. The cover is mounted on a lip and groove. The case snaps there with or without batteries. ...enjoy

twisted 18650 battery case
thingiverse

simple case sprint 18650 with 0.5mmprints nozzle set lengths FAST2 case 60 and 65 added sizes mmextra cap for different tolerancesi use the cover 0 tolerance and works Sprinter perfect environment: CR10 Rafts: is not compatible with: No Resolution:...

18650 Battery-Case
thingiverse

18650 case for two batteries and the ability to indicate when the batteries are empty plate with a small plate or two colors on top of the lid.For loaded, I actually wanted to have two plates with different colors, but unfortunately not my printer...

Dual 18650 Battery Case
thingiverse

This is a case designed to hold two batteries 18650. It is intended with two magnets (6 mm x 3 mm) are closed. One at the base and lid. I can not stress enough that people use in batteries loose, it's never a good (or safe idea) and many of the cases...

18650 Battery Case
18650 Battery Case
shapeways

battery box for a single 18650 Beautiful, large cap and a thick handle. ...The long thread makes it possible to fit protected batteries, which could be longer than 65 mm thick grip also makes it so it will not roll.

18650 Battery Case
18650 Battery Case
thingiverse

battery compartment for two 18650 Li-ion. ...Savely run the batteries and witches fully understood by replacing empty in the other direction load round.Update 07/24/2018: Mixer uploaded file (2,79).

QX7 18650 Battery Case
thingiverse

If you do not put a knot in about 3 mm, then the battery is not in contact (as most are on both sides 18650 good near flat) plane has little beyond 3D printing sticking out, which keeps the metal strip inside where the battery is placed.Step 4 after...

18650 Battery case.
thingiverse

18650 battery box, which is very low profile. maintain pressure. I oozes use to aid in adhesion to the surface, but it could not melt 360Sliced ​​in CuraPrinted in 3rd with Sprinter OctoPrint and BLTouch bed probe.Print Level Setting needed.Designed:...

18650 Battery Case
18650 Battery Case
thingiverse

a version up to 4 batteries.This is a support UPDATEAdded 18650. Use the holdertol.stl battery "for a tight fit, if a loose fit, use das, Battery holder.stl'.print configuration is preferred: Sprinter Alunar Prusa i3 Balsas. ...Is not compatible with:...

3x 18650 battery case
thingiverse

Boîte de stockage pour 3 18650.Fermeture avec batteries 2 Aimants diameter of 4 mm x 3 mm Sprinter (ou 2 mm) .print Setting: Dagoma D200 Rafts: This is not compatible with the subject: matter is not Resolution: 0.20 Filling : 25%

18650 Battery Case
18650 Battery Case
thingiverse

battery case for a single battery 18,650th

Dual 18650 Battery Case
Dual 18650 Battery Case
youmagine

Prints only 2 of the housing halves, then stick to the magnet and get the case ready.

Dual 18650 Battery Case
Dual 18650 Battery Case
youmagine

Prints only 2 of the housing halves, then stick to the magnet and get the case ready.

18650 battery case
18650 battery case
thingiverse

4x M3x6mm or M3x8mm4x M3 M3 washers4x nutswiresrefer here for more information: http: //regishsu.blogspot.tw/2015/11/3d-diy18650-battery-case.html

7 x 18650 battery case
thingiverse

A simple case 7 18650

18650 battery case with threwds
thingiverse

for only ~ 18650

18650 Battery Case (4 Batteries)
thingiverse

Case for holding parts 4 4x 18650 batteriesrequired magnets 6mm width x3mm depthno adhesive as a seat fixed print mark Sprinter configuration required: printer Creality: CR-10S Rafts: No No supports Resolution: 0.2 fill 25

Fatshark 18650 battery case holder
thingiverse

Holder offset for Fatshark 18650 case.More comfortable to use and offers the possibility of riding on the back of goggles.Print Sprinter Setting: Anet A8 Balsas: unsupported: no matter Resolution: 0.2 Filling: 100% Notes: 100 % filling post-printing...