19 rack 3d models
76824 3d models found related to 19 rack.thingiverse
Simple 19 inch rack Extension. ... Extend your rack with 1 height unit.
thingiverse
Usefull for cable management on 19" standard rack. Two sizes available. No screw required. ... Cut the "support" after printing.
thingiverse
A configurable spacer inserted between 19" rack rail and equipment mounted, eg. when mounting power strips on the rear rail. ... Number of "U" can be configured as well as the thickness of the spacer in millimetre.
thingiverse
In a 19" rack you can either mount a backplane or single connectors with Z-rails. I had a backplane mounted directly to the enclosure but wanted to add some single connectors, so I designed a small mouting plate that was printed faster than a piece...
thingiverse
This is a cable management solution for a 19-inch rack. With the cable management, small amounts of cables in a network or server cabinet can be easily and neatly laid out. The print consists of several parts and is modular, so modules can be chosen...
thingiverse
This is my 19" rack stand, so that your server doesn't lie flat on the ground and can even be mounted with the rails.. It works with 1U and 2U Units. I designed this extra for the Dell R710, but it should work with others aswell. Bear in mind that it...
thingiverse
parts needed for build: * 1x 19" rack case from [distrelec.de](https://www.distrelec.de/de/19-zoll-geraetekoffer-431x203x129mm-he-schwarz-rnd-components-rnd-455-00116/p/30064337) * 16x heat sinks from...
thingiverse
Currently testing this print, but it's designed to be used with a shelf to hold 2 Haivision encoders in a 1U 19" rack.
thingiverse
... N1 should be put on original plastic skrews (I glued them). I made it with freecad in one piece before cutting it. Freecad source file is included. More about the whole thing on my blog : http://www.bluemind.org/odroid-n1-enhanced-nas-19-rack/
thingiverse
This is a set of 10" to 19" rack adapters (1HU). I created simple Adapter plates with cornered holes for cage nuts and round holes for using standard nuts to mount the interface section to the 10" part. The 10" device is meant to be fitted in the...
thingiverse
These rack ears are designed to replace the wood cheeks on the case and fit in a 19" rack. There is one screw inside the case and 4 on the outside for each wood cheek. Remove the end wood completely and replace with these ears. The case is an odd...
cults3d
These rack ears are designed to replace the wood cheeks on the case and fit in a 19" rack. There is one screw inside the case and 4 on the outside for each wood cheek. Remove the end wood completely and replace with these ears. The case is an odd...
prusaprinters
These rack ears are designed to replace the wood cheeks on the case and fit in a 19" rack.There is one screw inside the case and 4 on the outside for each wood cheek. Remove the end wood completely and replace with these ears. The case is an odd...
grabcad
Parameters (width, height, depth and sheet metal thickness) can be set in "RACK Parametarski Sklop 1.iam" file (Assemble > Parameters). It can be selected to go up to 42U but it was only meant to be used as 6U, 9U and maybe 21U - I don't think...
thingiverse
19" Frame um das Modul darauf zu montieren. ... https://www.musicstore.de/fr_BE/EUR/DAP-Audio-2-HE-Rackblende-f-Modulsystem-10-Segmente/art-PAH0017160-000
thingiverse
19" Rack for Unifi 8POE & 5POE Need to be cut in tow for print
thingiverse
This 5mm acrylic laser cut allows to host up to 5 Raspberry Pi in a 19" rack. ... Screws are 3mm.
grabcad
19" RACK MOUNT PLASTIC ENCLOSURE http://www.gainta.com.tw Farnell Order Code: 1526723 SPC pro-POWER
thingiverse
Unifi Cloud Key Gen 2 support for 19" rack. ... It can be reversed for the left side.
thingiverse
Just a small bracket to mount a TL-SG1024 Switch from TP-Link in a 19" Rack.
thingiverse
... and 3 parts 19" rack to use 4 Odroid HC1. ...I use it to host my swarm cluster, more details on http://www.bluemind.org/odroid-hc1-based-swarm-cluster-19-rack/ I made it with freecad in one piece before cutting it. ...Freecad source file is included.
thingiverse
This is just an idea that I had to take the common 6" rack models such as: https://www.thingiverse.com/thing:3646002 https://www.thingiverse.com/thing:3593885 https://www.thingiverse.com/thing:2084736 and mount them in a common 19" server rack. ... ...