1x2 wood 3d models
68993 3d models found related to 1x2 wood.myminifactory
This filament spool holder is very simple, but effective. It is moveable so you can slide it along the 1x2 piece of wood with ease. Three M3x10 screws in the back provide for a tough grip on the wood to hold the part in its place. the angular...
thingiverse
If used on a hardwood, they may be okay, although without compression of the wood, they may be stressed enough to fracture. 1x2s in Canada (prob USA too) are a common dimension product, not actually 1" by 2" inches though, as the 1x2s we buy in...
myminifactory
... where the L-shape is on its side), and can fit basically any spool you have. I didn't have any 1x2 beams on me when I made this (however, they are actually 1.5" by .75" like Joel said in his video), but the measurements are sure to fit. ...Enjoy!
thingiverse
... best one so far. The Axle included in this Thingi is a remix of Vincent's original. I found that using the one in his thingi allowed the 2 brackets to separate and the spool would fall. Wood used for shelves - 2 inch x 1 inch = 5.08 x 2.54 cm
youmagine
Tuile selon le template Wyloch's Armory, 2,5''x2,5''x0.75''. L'utilité est de pouvoir incorporer un mur de 0.25'' sur une case tout en laissant une place de 1'' pour une figurine, c'est à dire socle d'une figurine de taille M. ... Wyloch's Armory...
thingiverse
I designed this simple hinge to sit on top of a 1x2 wood strip You can use a 5mm rod with nuts to make it work
thingiverse
Customized version of http://www.thingiverse.com/thing:652558 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=652558
thingiverse
Customized version of https://www.thingiverse.com/thing:3867358 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3867358
thingiverse
Customized version of https://www.thingiverse.com/thing:3867358 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3867358
thingiverse
Customized version of https://www.thingiverse.com/thing:3867358 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3867358
thingiverse
Customized version of https://www.thingiverse.com/thing:3610780 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3610780
thingiverse
I will end up using 3 of these stands to hold the edge of the crossbeams in the frame of the board, which is made up of 1x2 furring strips, with the 1in side facing downwards. The stand is 80mm on X and Y, and 100mm on Z. ... I'm printing the first...
myminifactory
Keeping it simple, a basic arm for mounting a standard roll of filament on a shelf made out of 1x2" wood. The design can be used as printed, or you can add two standard 608 (skateboard) bearings which sit on the printable bearing rods and allow for...
myminifactory
I've been mixing a lot of concrete lately and while an "egg beater" drill attachment works well for large buckets, I've found a 1x2" board is a good size for mixing smaller amounts. However, the edges are pretty sharp and uncomfortable for even short...
thingiverse
Note, the 1x2 is a tight fit if you don't sand it first, so slightly scale up the part if you're not intending to sand the wood first. Right now the "Speaker Stand Base" is used for both the base and top of the speaker stand. This seems to work...
thingiverse
Holder for hdmi splitter 1x2 from aliexpress. ... Держатель для HDMI разветвителя с алиэкспресс.
grabcad
This 3D Printable 1X2 Lego Brick made in fusion 360 can fit perfectly with real Legos.
thingiverse
A 1x2 Gridfinity drawer. ...The drawer body is recommended to be printed vertically with a little bit of support.
grabcad
This is a LEGO Plate 1X2 (3 plates = 1 brick). ...The plate similar with the plate 302301, but it does not need to be white.
cults3d
Box locker 1x2 to be stacked dimensions in cm: 6,30 x 12,60 x 6,20 use only supports between 5 and 10% from the bed
grabcad
This is a LEGO Tile 1X2, (3 tiles = brick). ...The tile is similar with the brick 306901, but it does not need to be white.
grabcad
This is a LEGO Brick 1X2 (3 plates = 1 brick). ...The plate similar with the plate 300401, but it does not need to be white.
thingiverse
This will hold a 1x2 seeedstudio grove module. ...It can be glued to a surface and then the Grove module can be inserted and removed.
pinshape
This is a LEGO Brick 1X2 . The "L" means that the brick is large ( 1 large brick = 3 small bricks ) . ...The brick is similar with the brick 300401 , but it does not need to be white .