2 5 in to 3 5 in hard drive adapter 3d models
3272618 3d models found related to 2 5 in to 3 5 in hard drive adapter.thingiverse
This is a simple lightweight tray adapter to be able to place a 2.5 in hdd/ssd in i a bay for a 3.5 in drive. ... It is made to be light and fast to print, taking strength from the drive that is in it.
thingiverse
Unfortunately the tray-less slide-in dock of my PC does not play well with 2.5" drives, so I went looking for an adapter to hold the 2.5" SATA drive in place while plugging it in. Browsing through Thingiverse I found this design:...
thingiverse
This is a hard drive adapter to hold my 2.5" SSD drive and snap it into a screwless 3.5" hard drive sled in my computer.
cults3d
Adapter for 2.5" hard drive or SSD to 3.5" slot; see pictures
thingiverse
I needed a 2.5" to 3.5" hard drive adapter with 3 mounting points (for the 3.5" hdd side). Here is my interpretation. ...I have included the step file if you want to make any changes.
thingiverse
2.5" Drive to 3.5" Drive Adapter. Should fit most applications. ... Super simplified, reversible, and thin for ease of printing.
thingiverse
The other major selling point is that this thing moves the connectors to be in a very similar location of where the 3.5" drives' connector would be. I use polycarbonate in a Raise3D N2+ to print these. ...However, it is up to you to make an educated...
thingiverse
------------------------------------------------------------------------------------------------------------------- Here is an adapter to be able to use 2.5 "hard drives or SATA SSDs in Synology brand NAS and using drawer racks. ... This notably allows...
thingiverse
It has the side mounting holes for the 2.5" drive and it has both the bottom and side threaded holes to fit in the 3.5" caddy, to the same specs as a Seagate hard drive. ...Uses about 10g of plastic.Works with a set of 4 or more M3 x5 standard PC...
thingiverse
simple 2.5" to 3.5" hdd adapter with 3 holes. holes align up perfectly. ... print in ABS to reduce chance of plastic warping once installed into a pc case.
thingiverse
Remix: Correct screw spacing. ... Allow for inset screw heads with print supports designed in the STL. Less material used in the bottom. Various options for side and/or bottom adapters for the 3.5 inch drive.
thingiverse
... drive or SSD into a desktop PC. ...Correctly placed holes for underside mounting of the 2.5" drive and the outer holes are correctly aligned and sized for standard coarse-thread case screws to self-tap into the plastic. ... Does not require supports
thingiverse
This adapter tray allows for the installation of two 2.5" drives into a single 3.5" bay. ... For more great projects, [check out my site](https://www.buidxyz.xyz)
myminifactory
Simple print that will allow you to install a 2.5" drive into a 3.5" drive tray. While maintaining alignment with the data & power connector. ... Hope you enjoy.
thingiverse
A simple and universal adapter to install one or two 2.5" laptop hard drives into a desktop computer. Allows for the 2.5" drives to be offset for right angle cables if needed. One of the models is a simple print and use version, just print them two...
thingiverse
... to build surface to help with the recessed screws. Mounts in standard drive bays and puts the wires as close to the original spot as I could get them. I got bored and just cut my lion out of the middle of it, works! ... Anyways, #Thank you!
thingiverse
Just a basic 2.5 to 3.5 adapter I designed up because I needed one for a computer I was working on. No frills, just a chunk of plastic with some holes. ...It'll print without supports if you print it upright (standing tall with the cutout at the top),...
thingiverse
Use this bracket to adapt the 2.5" drive for use in a 3.5" drive space. Instructions This is designed so that a UNC 6-32 screw can tap into the plastic of the 3.5" drive mounting holes. 2.5" drives use M3 screws - the holes for them on this bracket...
thingiverse
3.5" to 2.5" adapter for PC drives. ...May not work for certain configurations. Designed to adapt drive sleds from 3.5 to 2.5 for facilitating an SSD upgrade on an older machine.
prusaprinters
I designed this model to fit in a HP Z240 full tower chassis. ...This will probably only work in computers with tool-less drive installation that is similar to the HP design.
thingiverse
I know there are many 2.5 inch to 3.5 hard drive adapters , but this one is specifically Playstation 2 , its made to be slim so it doesent mess wit the airflow by blocking the vent holes that are in the expansion bay . ... There are mounting holes for...
cults3d
Disk Adapter , SSD 2.5 to 3.5 Mechanical Disk , for desktop computers , Caddy . Creation made for reasons that there are cases that do not have space for a 2.5 disk . ...very useful to replace a disk 3.5 to 2.5 of a machine.
prusaprinters
This adapter allows to put a 2.5 drive in a 3.5 bay keeping the connector in the same place.Dimensions and screw holes are exact taken from drives specifications.Useful if you have a server caddy.Model is upside down for printability without...
thingiverse
This adapter allows to put a 2.5 drive in a 3.5 bay keeping the connector in the same place. Dimensions and screw holes are exact taken from drives specifications. Useful if you have a server caddy. ... Design available in onshape.com:...
thingiverse
There are a number of 2.5" to 3.5" hard drive brackets on thingiverse, but ALL the other ones don't seem to be for hotswap server bays with drive caddies (because they don't mount the SSD in the required position). That may be because you can just...
thingiverse
Adapter hard drive 2.5 to dvd. ...Print Settings Printer Brand: RepRap Printer: Prusa i3 rework Rafts: No Supports: No Resolution: 0.2 Infill: 40
prusaprinters
Allows you to use a 3.5 in HDD hotswap bay with your more popular 2.5 in SSD's. ****Edit***I added two new files v2, I rounded off the edges I think it looks nicer. Enjoy!
thingiverse
Adapter for 3.5" to 2.5" drives. Designed for the CM Storm Scout case's drive bays but may work for others. Final dimensions not fully verified, print at own risk. A 9/64" or slightly smaller drill bit is needed to remove the sacrificial bridge,...
thingiverse
This adapter will allow you to use a 2.5" 7mm height SSD or hard drive (laptop form factor) in a Icy Dock hot swap bay. This was designed with the ICY Dock in mind, but should work for other similar designed hard disk enclosures. No supports...