2 grommet 3d models
933802 3d models found related to 2 grommet.thingiverse
I created this grommet that I use when I cut 2" holes in sheetrock or Desks to hide cables in-wall or at custom locations. ...Cable management necessity
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=273159 Instructions Using the following options: Grommet_Diameter = 70 build_plate_manual_y = 100 build_plate_manual_x = 100 Hole_Diameter = 50 build_plate_selector = 0 Font_Size = 8...
thingiverse
This 2" grommet perfectly fits a hole you would drill. I used a 2" hole saw but you could also drill a hole and use a jigsaw if you are careful. Do not drill closer than 1" to any edge, as that part is solid and part of the structure of the unit. The...
thingiverse
Emax Babyhawk 2 HD - Grommet to prevent rubbing of power cables.
prusaprinters
This is a super simple grommet I pulled together when building my home network cabinet. Simply cut a 2" hole in your cabinet and screw this bad boy down in it. ... Voila!</p>
thingiverse
3/8 interior hole 1/2 outer diameter How I Designed This Designed on 123D Design
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=273159 Instructions Using the following options: Hole_Diameter = 15 Top_Text = build_plate_manual_y = 100 build_plate_manual_x = 100 build_plate_selector = 0 Letter_Spacing = 1.3 Font_Size = 8...
prusaprinters
... in the bathroom. ...So I drilled a hole, measured twice, and designed a grommet to protect the cheap particle board from abrasions.Made in Tinkercad, it is easy to print and useful if you remember to print it before you put the lines through the hole.
thingiverse
Fits 2" hole. No cover. Made in sketchup free in inches. ...In cura 3 I had to scale up to x/63.5mm, y/63.5mm, z/31.7503 1"=25.4mm
thingiverse
This is designed as a 2 inch grommet, made out of two pieces that screw together for panels, fabric, or other thin type of material. The two halves screw together in about a half of a rotation. I printed with no Brim or Supports, and it printed...
grabcad
You know those holes in your work desks used to route wires through? ...Well I wanted a plug for one that I wasn't using so I could get a flat surface back. I made this for a 2" hole that fits snug so that it stays in place. ...Just print and plug!
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=38819 Instructions Using the following options: caseThickness = 3.5 $fn = 35 cableHoleDiameter = 0 caseHoleDiameter = 19.05 catchAngle = 55 thickness = 1.2 sliceAngle = 80 catchHeight = 1...
thingiverse
I remixed one of the several covers available for the Skelestruder filament sensor with the incoming grommet holder from the Prusa MK3s lid and wound up with a filament cover that holds the grommet and incoming tube from my Palette 2. ...Also able to...
thingiverse
Customized version of https://www.thingiverse.com/thing:273159 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=273159
thingiverse
Customized version of https://www.thingiverse.com/thing:4372453 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4372453
thingiverse
Customized version of http://www.thingiverse.com/thing:273159 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=273159
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/jbl30AS6rwM
thingiverse
This is a 2-piece passthrough grommet for a starlink or similar cable where you cannot take the ends off. Push the cable into the inner grommet, then add the outer grommet and turn it to fully cover the cable and hole. You'll probably want to...
thingiverse
This is a clip which accepts the filament tube grommet supplied by Mosaic Mfg for the Palette 2. It clips directly onto the filament clamp of the Titan Aero. I include a guide to support the tube above the grommet because as the print head moves...
thingiverse
Customized version of https://www.thingiverse.com/thing:3204763 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3204763
thingiverse
Customized version of http://www.thingiverse.com/thing:38819 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=38819 Instructions Using the following options:...
thingiverse
Customized version of http://www.thingiverse.com/thing:38819 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=38819 Instructions Using the following options: ...
thingiverse
Customized version of https://www.thingiverse.com/thing:273159 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=273159
thingiverse
A simple 2" grommet to drill into your table and allow cables to pass through. ...Good height for IKEA linnmon table.
cults3d
The sleeve seats firmly into the 2" hole, and the cover snaps securely in place and can be rotated after assembly. If anybody wants additional sizes let me know, because now that the model is all set up I can bang out alternate diameters no...
thingiverse
Dual Grommet, large hole is 1' and small hole is 5/8, countersunk for a 10-24 allen bolt i believe, EMS EHLERSMOTORSPORTS
thingiverse
The sleeve seats firmly into the 2" hole, and the cover snaps securely in place and can be rotated after assembly. If anybody wants additional sizes let me know, because now that the model is all set up I can bang out alternate diameters no...
grabcad
... find an accurate model for one that I wanted to use so I created it. This was modeled as precise as my digital calipers would allow. It has multiple configurations to represent the (4) different positions that the cable grommet can be adjusted to.
thingiverse
I couldn't find the right wall grommet for my antenna cable so I made one. This is designed for a 3/4 inch (19mm) hole (approx) and RG-8X coax cable about 6.4 mm in diameter. outside diameter of the flange is 40 mm, 5 mm thick. Length is 30 mm. I...