2 ml eppendorf tubes 3d models

Adapter for a 2-mL Eppendorf LoBind tube for use in a 50-mL conical tube that is provided with the Amicon® Pro System.

* depending on printing technique, material and tubes used, the tube holes might be a little tight, but they get nicely fit with ~10mm felt polishing wheel/cone (just don't start of with high speed or you will melt the material and get the felt...

* depending on printing technique, material and tubes used, the tube holes might be a little tight, but they get nicely fit with ~10mm felt polishing wheel/cone (just don't start of with high speed or you will melt the material and get the felt...

This is a tube rack that securely holds standard 1.5 mL and 2.0 mL tubes microcentrifuge tubes. I liked MS3FGX's microcentrifuge tube rack but found that when I pushed down on tubes to close them, it made the whole thing flex down and it didn't fill...

This is a solid model of the 2 ml eppendorf tube Modeled by Bobby Dyer a medical device engineer based in Boston MA Rendering and solidworks model

8 by 2 1.5 ml Eppendorf Tube Rack

I design for use with Eppendorf test tube (2 ml.). ...It can be hold 2x6 tube which tend to duplicate for 6 experiments.

Here are two versions of an Eppendorf tube rack made to hold a dozen large volume (2.0 or 2.2 ml) tubes. These tubes are different shapes than the traditional 1.5 / 1.7 ml Eppendorf tubes. One of my team members requested I make a tube rack that...

Carrier for 6 2 ml eppendorf tubes

This tube insert is used as an adaptor for a barocycler tube to make it compatible with equipment sized for a 1.5 or 2 mL Eppendorf tube. ...Can be used for tissue homogenization, centrifugation, heating and shaking.

Multi-Halter-Z: 4x 50 mL falcon tube 8x 15 mL falcon tube 9x 1.5 and 2 mL Eppendorf tube

This tube insert is used as an adaptor for a barocycler tube to make it compatible with equipment sized for a 1.5 or 2 mL Eppendorf tube. ...Can be used for tissue homogenization, centrifugation, heating and shaking.</p> Category: Biology

Multi-Halter-A: - 2x 50 mL falcon tube - 3x 15 mL falcon tube - 15x 1.5 mL Eppendorf tube - 9 rows PCR-tubes Multi-Halter-L: - 2x 50 mL falcon tube - 4x 15 mL falcon tube - 6x 1.5 and 2 mL Eppendorf tube Multi-Halter-Z: - 4x 50 mL falcon tube - 8x...

The rack can hold standard 1.5 and 2 ml Eppendorf tubes. You can quickly adjust for any number of the tube you need. Also, you can choose the distance between the Eppendorf tubes to make them stand tight or rarer. It is possible to add a skirt for...

This simple stand for 1.5-2 ml Eppendorf test tubes can be used when measuring on a laboratory balance scale, etc. It can be printed without supports, if placed upside down! Source code (.stp & .3dm) is also provided, should you want to modify the...

This is an Eppendorf tube holder made to hold 0.5 mL, 1.5 mL and 2.0 mL Eppendorf tubes. It is made to hold a tube on a balance. Therefor it is scaled a bit bigger than it has to be, for a stable stand. ...One side holds the 1.5 mL and 2.0 mL tubes and...

Here is a simple holder for a 1.5 ml or 2 ml microcentrifuge (‘Eppendorf’) tube, as part of my 3d printing labware range. ...The goal was to make items which: - Are functional (in this case securely holding tubes upright) - Use minimal plastic, and so...

Eppendorf PCR tube 0.5 ml (0030108035). ...The lid is not 100% accurate, yet the outer dimensions and inner dimensions fit very well to the actual tubes.

Easy to print 4x 5ml eppendorf tube holder.

A centrifuge hub designed to hold four 2.5 mL Eppendorf tubes. ... Tested up to 10,000 RPM Instructions 1) Laser cut one center hub and four petals 2) Tap the small holes on the petals with a M3 thread 3) Screw together with 4 M3 screws (15-20 mm long)...

Eppendorf 1.5 ml

I designed stand for 4 oder 8 times 1.5 mL Eppendorf tubes and want to share them with you. ... Others can be designed and uploaded on request.

eppendorf tubes holder

By using this adapter you can put an eppendorf tube in a falcon 15 mL, you will say, what is the use? ...I use that with Frac-920 of AKTA purifier to have the liquid droplet in the middle of the tube and not just close to the edge of the tube (when i...

simple but fancy eppendorf tubes holder, 6 x 24 holes Print Settings Printer: vertex3d Rafts: No Supports: No Resolution: 0.2 Infill: 25% Notes: take care, due to the big surface may result difficult to detatch from heated bed

So this is a really simple modification of the previous design to use 10×3 mm disk magnets (3) but customised for common 2 mL Eppendorf-style tubes they use in the lab (4). Like the previous model, this has channels you slide the magnets into, and...

For a more fancy outcome, you can print the first two layers in another color. One rack of size 16x4 will cost you ~1.50 Euro of plastic. ... Make sure to print it with the springs facing down.

This Eppendorf/Centrifuge tube holder is used for packing under nitrogen - flow of nitrogen goes into a downward-facing funnel. I put my samples into the tubes, put them in the rack under the funnel, wait for a few minutes for nitrogen to displace...

A holder for two tubes, either 15 ml Falcon tubes or 5 ml Eppedorf tubes.

We needed some new Eppendorf racks so I made a few and thought they might be worth sharing.