2 prong switch 3d models
978106 3d models found related to 2 prong switch.thingiverse
Here is a tactile switch holder I am using to open and close the shuttle bay doors with Arduino Micro in the tank. Screws to the side of frame under front bumper. Drill out the wire holes to .120". Please note the tactile switch will only go in once....
thingiverse
Normally, action cameras extensions and mounts are 2-prong on the action camera side and 3 Prong on the other, this way everything fits but it only goes in one direction… sometimes you need to join two 3 prong ends of action camera accessories...
thingiverse
... Switch Box was designed to mount a 5 pin rocker car switch. ... The switch I use can be found here: (https://www.aliexpress.com/item/LED-Car-Switch-Light-Truck-Light-Toggle-Switch-5pin-Waterproof-Spot-Driving-LED-Light-Bar-Tray/32818193523.html). ...
thingiverse
... out. 9/12/17-------- This is just a 2 prong mount, i got tired of making them everytime and no one had them that i could find. so you can build whatever and when you are ready to add the mount just input it and add done. ...much faster and easier.
thingiverse
This is a two prong to two prong GoPro Adapter. ...I will be using this to attach a GoPro mount to another GoPro mount, specifically the bike mount to a shotgun mount to enable me to attach a gimbal to the bike mount, and the other end to whatever I...
thingiverse
6 fasteners, a blanket and 2 poles Hammock - 2 fasteners and a blanket Emergency Tent -? 4 fasteners and a plastic sheet or tarp Greenhouse or row guard - Use a number of fasteners and clear plastic to create a greenhouse Food transport - Use...
pinshape
6 fasteners, a blanket and 2 poles Hammock - 2 fasteners and a blanket Emergency Tent -? 4 fasteners and a plastic sheet or tarp Greenhouse or row guard - Use a number of fasteners and clear plastic to create a greenhouse Food transport - Use some...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_bar_th = 3.2 gopro_secondary_what = double gopro_bar_screw_nut_d = 6.01 gopro_captive_rod_angle = 45 gopro_bar_screw_head_d = 6.2...
thingiverse
I needed a longer version of Gornstein123's 2 prong by 2 prong GoPro Adapter, so I "smooshed" (is that the correct term?) four of his together in Cura and then grouped them as one object, then exported it as an .stl file. The distance from end hole...
prusaprinters
This contains both sides and a clip for an American style 2-prong body cord. Prong holes are enlarged to prevent minor print defects from affecting assembly. The holes are threaded and accept M3x10 and one M3x16 screws. The 16mm screw is for the...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_captive_protruding_h = 0.5 gopro_ext_th = 3 gopro_bar_screw_shoulder_th = 4.5 gopro_captive_rod_id = 4.8 gopro_secondary_what = rod...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_bar_screw_d = 3 gopro_ext_th = 3 gopro_ext_len = 0 gopro_captive_rod_id = 3.8 gopro_bar_screw_nut_d = 6.01 gopro_secondary_rotated = 0...
thingiverse
This is a protective mount that I designed to house a 12015792 - Delphi Weather Pack 2 Way Black Sealed Female Connector. This allows me to unplug and remove seasonal electronics and store the vehicle mounted connector in a protective case that is...
thingiverse
My Yongnu Light had different 2 prong mount, most were 4 prong, so I designed this adapter so it would convert to a standard go pro mount. ... No supports needed
thingiverse
This housing is for the standard 2-Prong body cords primarily used in the USA for Foil and Sabre. It's best use is for saving cost while repairing club equipment. The cost to print both sides is about $0.17. I would not compete with this design nor...
myminifactory
This housing is for the standard 2-Prong body cords primarily used in the USA for Foil and Sabre. It's best use is for saving cost while repairing club equipment. The cost to print both sides is about $0.17. I would not compete with this design nor...
thingiverse
This is a mounting bracket to attach to a phone case or other gadget. ...Works with the Ultimate Addons 3 prong mountshttp://www.ultimateaddons.com/Adapters/25mm_to_3_Prong_Adapter
thingiverse
Thick mount for Insta360 GO2 with gopro style prongs. I printed it with 20% infil so it does some protection and I can slap it on FPV drone :) Lens does not stick out and there are simple blocks on the back preventing it from falling out. ...
thingiverse
Customized version of http://www.thingiverse.com/thing:62800 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=62800
thingiverse
The holes for the bearings are 23.3 mm and do not require any sanding to put in bearings. ... Holds ceramic and/or normal metal 608 bearings
thingiverse
I have the Pazzo LED Shelf Lamp and wanted to use my USB fast charger however I was slanting due to size. ...Made this to fit around the 2 prong plug and support my ugreen charger block.
thingiverse
A small adapter plate to convert a quarter-turn mount to 2-pronged GoPro. There are plenty of models to convert to a 3-pronged GoPro mount, but I struggled to find one to go to the other side of the GoPro mount. ... This is designed to accept a...
prusaprinters
A small adapter plate to convert a quarter-turn mount to 2-pronged GoPro. ...There are plenty of models to convert to a 3-pronged GoPro mount, but I struggled to find one to go to the other side of the GoPro mount. This is designed to accept a quarter...
thingiverse
I created a bottom mount for my cycling computer which allows for mounting of GoPro. This attachment allows mounting of a headlight to that GoPro mount instead. Best printed in the orientation as downloaded with a Brim. no other supports needed....
thingiverse
I have not gotten to print this out yet will put a picture up when it is complete.