2 shower heads 3d models
1042502 3d models found related to 2 shower heads.cults3d
Pocket shower head, fits in every pocket! 3 hours to print, no support. ...no no no yes
thingiverse
Pocket shower head, fits in every pocket! 3 hours to print, no support. ...no no no yes https://www.youtube.com/watch?v=K-lnBUERIa0
prusaprinters
<p>3 hours to print,no support. ...no no no yes</p><figure class="media"><oembed url="https://www.youtube.com/watch?v=K-lnBUERIa0"></oembed></figure>
thingiverse
Customized version of http://www.thingiverse.com/thing:47541 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=47541 Instructions Using the following options:...
thingiverse
... with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=47541 Instructions Using the following options: headDiameter = 2 concentricCircles = 3 headLength = 1.5 jetApertureDiameter = 0.0625 jetsPerRow = 8 jetType = 1 smoothness = 65
thingiverse
Customized version of https://www.thingiverse.com/thing:47541 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=47541
thingiverse
Customized version of http://www.thingiverse.com/thing:47541 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=47541
cults3d
Bathtub water inlet G1/2 Zoll. ...Simply exchange with shower head. ...Simply hang it on the edge of the bathtub
thingiverse
Customized version of http://www.thingiverse.com/thing:47541 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=47541
thingiverse
My mini shower head was too much for the wife.. So, this one has full flow with a softer feel. Bent at 45 angle to line up with most US shower extensions. This is also made to work at multiple angles. Flip your extension pipe 180 degrees for a...
thingiverse
...So this is the opposite, 1/2 NPT female to screw onto the shower head, then 3/4 NPT male to screw the garden hose onto it. If you're using this for cleaning dishes or actually taking a shower, I recommend limiting the hose length as much as you can.
cults3d
It's a high-flow shower head! ...Will fit on any standard 1/2" shower head pipe. ...Buy this if you want to allow it to swivel (http://www.amazon.com/Opella-205-995-280-Shower-Swivel-Nickel/dp/B0038FLVRK).
thingiverse
3 different sized shower heads normal, small, and tiny read print settings section
thingiverse
Will fit on any standard 1/2" shower head pipe. Buy this if you want to allow it to swivel (http://www.amazon.com/Opella-205-995-280-Shower-Swivel-Nickel/dp/B0038FLVRK). Instructions I've...
thingiverse
This is an adapter for a 1 1/2" shower head pipe to a standard hand help sprayer used for a hand-held shower head or bidet sprayer. ... This design is wider and stronger than my earlier, narrow design (below): ...
thingiverse
Will fit on any standard 1/2" shower head pipe. Buy this if you want to allow it to swivel (http://www.amazon.com/Opella-205-995-280-Shower-Swivel-Nickel/dp/B0038FLVRK). Use teflon tape for a good seal between the pipe and the head. ...The V2 file has a...
cults3d
Rawrrrr!" Will fit on any standard 1/2" shower head pipe. Buy this if you want to allow it to swivel (http://www.amazon.com/Opella-205-995-280-Shower-Swivel-Nickel/dp/B0038FLVRK). Use teflon tape for a good seal between the pipe and the head. The V2...
thingiverse
#Really Awesome Two Piece Low Flow Shower Head ## Why Because of the droughts in California I wanted to replace my old 2.5gpm shower heads with something lower flow but still maintain a strong water stream. I measure the consumption to be around...
cults3d
This shower, has a universal thread to put in the tubes, it is recommended to use a little Teflon tape. If larger is needed, it should be enlarged proportionally so that the thread is not deformed. ... No brackets required, wall thickness should be 1mm...
myminifactory
NEEEEEERRRRRDS! ... This is a set of five orc nerd heads. ... They will be well suited for 28mm tabletop orcs.
myminifactory
The Talaurisa Regulars heads from the first part of the War for Cittonnen. ... Models are 32mm scale and are pre-supported.
myminifactory
The second set of generic heads from the first part of the War for Cittonnen. ... Models are 32mm scale and are pre-supported.
myminifactory
A set of five halloween inspired ork heads, wearing pumpkins to....blend in? Look more orky? ...I think they're inspired by the season!
myminifactory
The Yplitacatic City Guard heads from the first part of the War for Cittonnen. ... Models are 32mm scale and are pre-supported.