2 way vise 3d models

My version of Prusa MMU2 PTFE Tubes Separator by fucosk a 5-way tube separator, the only difference is that I rounded off the corners a bit

A 3 way clamp fo a 1 inch cross section - used it to make a Insulating cover for my ender 3 v2

A 5 way PVC joint that is designed to fit 3/4" PVC pipe but can be scaled to fit any size.

The way to roll: Portable, foldable wheelchair rampIntroductionIn our school project, we focused on creating an innovative solution to improve accessibility: a wheelchair ramp that is both easy to build and affordable. This project aligns with our...

The model was created using Autodesk 3ds Max 2010, rendered with Vray 2.20.02. Please take a moment to rate the model; it's essential for us. 3D model available in these formats: 3ds Max 2010 (.max), Autodesk FBX 2006 (.fbx), OBJ (.obj) Scene...

The model was created using Autodesk 3ds Max 2010 and rendered with Vray 2.20.02, including all necessary materials. Please don't forget to rate this model; it's very important to us. This 3D model is available in several formats: 3ds Max 2010...

Simple cap to fit over a 7-way trailer plug. ... After printing up a trailer hitch organizer the 7-way was going to fill with water. This will help keep the water out and the plug clean. ... Suggest printing with TPU

... ways inside the wall. ...You can put a 5mm ball in the entrance and let it slide. If you use the magnetic ball, you can control the balls, or make a chain and get through the spiral way.The outfline of this tube is parabolic. ...I hope you like it. 

# way ball valve Manufacturer Part #: 6392790 3/8 Barb Ports Polypropylene Three- Way Ball Valve 1/4" FNPT Buna Blue Handle Manufacturer: SMC http://www.specialtymfg.com/Specialty manufacturing (651) 653.0599 FP 639-6B6B6B-B,BLU HDL 3/8" barb FP...

... inside the wall. ...You can put a 5mm ball in the entrance and let it slide. If you use the magnetic ball, you can control the balls, or make a chain and get through the spiral way.The outfline of this tube is parabolic. ... I hope you like it.

... some flexible rubber material. Envision a piece of thick, pliable latex, similar to that found in high-quality gloves. This will serve as the foundation for your one-way valve, allowing air to flow out while preventing it from entering back in.

... and irrigation purposes, as it ensures a continuous flow of water to multiple points at once. The three-way connector directs the water stream into separate hose connections, enhancing efficiency and convenience in high-demand situations.

... location while maintaining temperature and pressure levels, ensuring efficient distribution of heat. Ideal for use in various applications, a three-way valve actuator plays a crucial role in maintaining comfort and energy efficiency in heat systems.

A two-way valve is a device that controls the flow of fluids by allowing them to pass through in one direction while preventing backflow in the other direction. It can be used for various purposes such as regulating pressure, controlling the flow...

Simple AR-15 lower vise block. ...This is my first model, if there are issues with dimensions please let me know.

A centering vise and centralizer are featured in a space-saving hard disk drive (HDD) setup, ensuring precise alignment and stability during the installation process.

This is a hand star wheel that fits a 11.8mm hexagon shaft on a milling vise. Printer: MK3s,  Filament: Esun PETG Blue

Modeling Press (Grinder Vise) Exercise from the book "Drawing and Graphic Communication Third Edition"; appreciate the model by hitting the '♥' button. ...No payment needed, just enjoy!

I offer a replacement power tool vise from Parkside. ... To complete the plastic part you will need a standard m14 nut.

The vise design is derived from data obtained via Kurt's website and their given dimensions, making it a dependable representation for practical use.

The soft jaws I had bought from various sources all did not fit on my vise, so I decided to design my own.

The Vise is too short when putting snowboard on top. ... The top groove can be filled with hot glue for traction.

Secure the object firmly onto the worktable using a vise positioned under the center cup, applying steady pressure with two gentle bites to ensure stability and control.

The assembly process involves attaching various components, including the vise jaws, handle and clamping mechanism, to create a versatile tool for working with metal and wood. Once complete, the Angle Tool Vise Assembly will provide a sturdy and...

The Hand Vise 01 features a sturdy steel construction and a smooth operating mechanism that enables users to easily position and adjust the vise as needed. ...With its precision-crafted jaws and adjustable tension, this hand vise is perfect for holding...

First project with Fusion 360. ... Soft jaws for a very cheap C clamp vise with 36mm jaws. ... The holes are 1mm to 6mm in diameter

This calls for a Starrett 162 Pin Vise kit. ...It comes equipped with two compact storage containers for drill bits and pins.

This is a simple extension of the vise to clamp down small things to a miter saw. ...i'm including a solidworks file.

Soft jaws for a 6" vise. Holes on back are locations to epoxy in magnets. ... Parts were printed with 3 shell, 80% infill.

A mount for the nano vise on the 1/4PT Flexible Oil Coolant Pipes commonly used to make a soldering helping hand station