2002 saab 9 3 cup holder 3d models
1115325 3d models found related to 2002 saab 9 3 cup holder.thingiverse
Saab 9-3 custom cupholder. ...Both cupholders in my 2007 Saab 9-3 worked well with the gear shifter and my water bottle. ...I designed this to fit in the plastic section next to the passenger seat opposite side of the handbrake.
thingiverse
This is a replacement for Saab p/n 4422184, which is a small storage shelf for 1999-2002/3 9-3's. This sits near the base of the center console, right behind the transmission shift handle. It fits my 2003 convertible. This will hold a 2" Oil...
thingiverse
Got a new phone (Axon 7 Mini) but have the same Saab with the gaping hole in the center console from where the cup holder used to go. ...The old LG G4 holder deformed in the heat, so hopefully the thicker holder in this version will hold up better.
thingiverse
Cup holder that attaches to the console of a Saab 9-5 99-09. Just lift the shifter trim and clip in. The clip slides into the cup holder slot. ... Supports for just the clip.
thingiverse
It fits behind the back seat side door panels on a Saab 9-3 convertible, keeping the panels from being dented in or deformed. This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/andk7hnZ0gU You might want to...
thingiverse
Cup holder for Saab 9-3 1998-2002 (& SAAB 900 1994-1998) Cup holder is attached to the knobs of middle ventilation grille in dashboard. Instructions: 1. Print (ABS) the following parts: Top x 1 Bottom x 1 Side x 2 Back x 1 (Mirror in RHD cars?) 2. It...
thingiverse
Designed an umbrella mount to be mounted on the two metal rings in the rear of the boot of a Saab 9-3. This was designed for a 2010 Saab however, will likely fit other models with these rings (see photos). I've added the Solidworks file also.
thingiverse
This is a Iphone 6 holder that is designed to fit to the Saab 9-3 NG. It has holes cut out for the charging port, the 3.5mm headphone jack and the speaker. The holder is designed to work with a iPhone 6 with a thin TPU case. A plain iPhone will fit...
thingiverse
Read further down for details on that.] This is a smartphone holder designed specifically for the NG (new generation) Saab 9-3, pre-interior-facelift. That's 2004, 2005, and 2006 for the convertible, plus 2003 for the sedan. The phone slides in on...
cults3d
Read further down for details on that.] This is a smartphone holder designed specifically for the NG (new generation) Saab 9-3, pre-interior-facelift. That's 2004, 2005, and 2006 for the convertible, plus 2003 for the sedan. The phone slides in on...
thingiverse
Replaces Saab 4381083 --------------------- Our car lost the original covers more than one time. In the car-wash or while driving fast. So I made something more individual. ... The part should be printed in ABS, PETG or another heat-resistance...
thingiverse
Saab 9-3 in profile. Can be used as a keychain or hung in the rearview mirror. ...Just change the size.
thingiverse
Cup holder expander for larger containers in a 2002 subaru outback.. ...may work for many other vehicles.
cults3d
Cup holder expander for larger containers in a 2002 subaru outback.. ...may work for many other vehicles.
thingiverse
These are the snap clips that help hold the rear spoiler down on certain NG900's/OG9-3's(1994-2002). The top portion is tricky on FDM machines and usually needs to be printed in at least 0.6 or finer. SLA printers should be able to make these easily....
thingiverse
Here is a cup holder for the classic SAAB 900 I designed. The cupholder clips onto the ashtray and will hold most diameter drink containers. Should work for any C900 from 1978 - 1993. I have used the cupholder personally for about a year and it...
thingiverse
This is a courtesy (reading) light holder for a 1999-2002/3 SAAB 9-3. It is the mating part of https://www.thingiverse.com/thing:221712 This fits my Saab 9-3 2003 convertible. It is similar to SAAB p/n 2381365. I recommend making this with ABS due...
thingiverse
This is my version of additional cupholder in central console for Saab 9-3 SS (2005-2010). https://www.eeuroparts.com/Parts/48578/Cup-Holder-Center-Console-12842692/ I didn't have an original part to make measurements but this one fits very well,...
thingiverse
A-pillar holder with ball joint. ... Glue on holder for specific phone
thingiverse
I've included another STL and updated the assembly to include an insert that allows the holder to work with the LG G4's stock body/shape. It basically just fills in the gap between the generously large arms of holder and the slimmer body of the stock...
prusaprinters
Figure there's a very slim chance that someone else might have this exact same setup. I'll make a more universal phone holder sometime in the future, but this serves me well right now. UPDATE! I've included another STL and updated the assembly to...
thingiverse
This is a 3D-model I made using Fusion360 for my sister's Saab 9-3. I tested the knob myself, and it works like a charm! I know parts for Saabs can be a rarity, if not, expensive. ...So, I hope this knob can help someone who can't find it!
thingiverse
Корпус антенны для saab 9-3 (2G) Пару моментов по модели. Заполнения я ставил 0. Слои дна тоже 0. Стенки ставил, чтоб перекрывали всю модель внутри. Поддержки были включены. Высота слоя была 0.3 мм. ...Печатал отдельно с 9-ого слоя (сама антенна) и...
thingiverse
A phone holder part for SAAB 9-5 (2003), it need parts from an old holder to be completed. ... Has a cut out SAAB logo
thingiverse
... size. Print at 100% infill using a material that won't warp from sitting in a car. Originally designed for the Saab 9-3 & 9-5 F40 transmission. May work with F35 and F23 transmissions. ...Should also work in the Cobalt SS, Opel Vectra, etc.
thingiverse
The design is based on the SAAB 9-3 sportscombi but with a wide bodykit to fit the dimensions of the K989 chassis and a Hirsch inspired wing in the back. I modeled the body in blender with some 9-3 blueprints as a guide to get the dimensions of the...
prusaprinters
This is a self-designed body for a WL-toys K989 rc car. The design is based on the SAAB 9-3 sportscombi but with a wide bodykit to fit the dimensions of the K989 chassis and a Hirsch inspired wing in the back. I modeled the body in blender with some...