2012 sea doo se 130 3d models

The 3D model was created on real car base. It’s created accurately, in real units of measurement, qualitatively and maximally close to the original. Model formats: - *.max (3ds Max 2008 scanline) - *.max (3ds Max 2008 vray) - *.fbx (Multi...

The 3D model was created on real car base. It’s created accurately, in real units of measurement, qualitatively and maximally close to the original.Model formats: - *.max (3ds Max 2008 scanline) - *.max (3ds Max 2008 vray) - *.fbx (Multi Format) -...

The 3D model was created on real car base. It’s created accurately, in real units of measurement, qualitatively and maximally close to the original.Model formats: - *.max (3ds Max 2008 scanline) - *.max (3ds Max 2008 vray) - *.fbx (Multi Format) -...

2012_Sea-Doo_GTI

2012_Sea-Doo_GTI

This is the Sea-Doo LETTER - *Arctic Cat LETTER: https://www.thingiverse.com/thing:4125032 * - *Arctic Cat LOGO: https://www.thingiverse.com/thing:4136505 * - *BMW LOGO: https://www.thingiverse.com/thing:4249695* - *Honda LOGO:...

fits 90's era SEA DOO

Sea-Doo front cover hinge. ... Custom made replacement for Sea-Doo original hinge with P/N: 269 500 704 Item 37 on chart found on Sea-Doo RXP and others If you like what I'm doing, please consider supporting me https://www.buymeacoffee.com/taguvove

I lost the nut to my DESS post on my Sea Doo so I made one. ... It's 20mm with a 1.5mm pitch.

... wear ring for pump. ... Fits Sea-Doo Challenger 1800/ GTX /RXP /RXT /Speedster /Sportster year 2044-2007 dimensions Dia:170mm Thick: 5.5 Height: 78.5mm If you like what I'm doing, please consider supporting me https://www.buymeacoffee.com/taguvove

This is a bracket to mount Ultimate Ears Megaboom on Sea-doo GTR, problaby fits most sea-doo's with similar glove box lid. Drill two holes in glove box lid and mount it with Ø4mm screws, washers and nuts. ... Attach the speaker with two 20mm wide...

Sea-Doo grommet for cable harness & gas spring to open front cover. Fits Seadoo RXP and others. *edit 2021-04-25 Upper flange adjusted thickness with 1mm. ... If you like what I'm doing, please consider supporting me ...

......http://www.thingiverse.com/apps/customizer/run?thing_id=52734 Instructions Using the following options: font_size = 10 message = SEA-DOO stick_width = 11 flat_bottom = 1 stick_thickness = 3 font_thickness = 5 Font = write/orbitron.dxf hole_radius = 3

If you already have a Sea Doo Chill Shade installed and don't use it anymore, this is made to fit the EXACT location of the shade's mounting bracket - no new holes! Made to fit a Spark's footwell but can be fitted pretty much anywhere you need to...

Well look no further, this is the perfect cupholder for your Sea Doo Spark!Fits any year Spark 2UP or 3UP (Trixx included)Holds both slim cans and soda/beer cans (up to 16oz!)Handy sunglasses holder in between the cupsMounts to the footwell on either...

This is a replacement nut for a Sea-Doo and Ski-Doo DESS switch nut. (Original OEM# 278000508 New OEM# 278002963) I modified to have 4 leverage points, instead of the normal 3, negating the need for a special tool from BRP. ...

OIL Cap For SEA-DOO Spark

Sea Doo Part # 273000006 Air box clip / retainer. It will fit the air box on a 787 engine possibly others. ...I installed them on a 97 XP.

RAVE Valve from 1999 Sea Doo GSX limited. ...First real complex part and assembly in a CAD class in community college so not perfect.

We have a 1994 and 1995 Sea Doo SPi Jet ski's. We we recovered the seats and the corner reinforcements needed replacing. ...There were none to be found on replacement site so I designed my own.

... a replacement part for it as the air filter is also kept in place by this no zip ties are needed anymore. ... Fits at least a Sea-Doo SP 1995 jetski with at single carburator Rotax 587 engine, might fit other engines / carburator configurations aswell.

Device to hold throttle on jet ski. ...Allows for various throttle settings and a thumb tab for quick release. Fits newest Sea Doo Spark models. ...I designed it for mine to help hold the throttle and relieve hand pain while I pull a tube.

This is a tool for removing Sea-Doo waterpump impeller. It fits over the impeller blades. There are two versions, one with a handle and one with 1/2 inch square socket. ... If you like what I'm doing, please consider supporting me ...

My Sea-Doo DESS key decided to crumple itself to death... No matter.. I haz a 3D printer to make a new thingi for it...That way I can salvage the chip without needing to code a new one...added a personal message whilst I was at it too.... Feel free...

My Sea-Doo DESS key decided to crumple itself to death... No matter.. I haz a 3D printer to make a new thingi for it...That way I can salvage the chip without needing to code a new one...added a personal message whilst I was at it too.... Feel free...

Cup holder for the sea-doo spark, this requires no drilling and fits into an existing hole from the factory. Print normally (I used 15% infill) FDM/ABS I use the monoprice voxel (it barely fits on the platform) For mounting its threaded for a...

This keeps the keys from getting stuck in the lynq brackets.Cut two lengths of pipe 15" longInstallation:Extend the ski pylon and lynq attach points on your sea doo to their “in use” positionsSnap the upper fitting onto the top of the ski pylonSnap...

Bought a used Sea-Doo SP 1995 jetski which didn´t have the start/stop button in the handle bar so I decided to design a replacement part for it to not need to push on the micro switch directly Fits at least a Sea-Doo SP 1995 jetski but will probably...

Sea Doo 1995/96 seat corner protectors - might fit other years / models....? Used Creality TPU filament at their recommended settings - not a real complex part so... ... Left and right side in file - mirrored images.

This is a bracket to mount JBL Charge 3 on Sea-doo GTR, problaby fits most sea-doo's with similar glove box lid. I angled the speaker front up towards the riders head. Drill two holes in glove box lid and mount it with Ø4mm screws, washers and...