20x20 frame 3d models
106524 3d models found related to 20x20 frame.thingiverse
This is a simple frame for FrSky R9MM/R9MINI to mount it neatly in a 20x20 frame. It fits the receiver in 1 layer of heat shrink tubing tightly. The top plate should be enough to sandwich the receiver. A version with zip tie guides is also...
thingiverse
A guide that bolts to 20x20 aluminum frame that directs wires 90* from the rail. ...Originally designed to be used with this cable link guide, https://www.thingiverse.com/thing:10915 I ended up not using the links, and just used the guide to direct the...
thingiverse
Adapter for a "whoop" size (26x26 mm) flight controller and a frame with 20x20 mm mounting holes. Holes in adapter are for 2.5 mm diameter screws. Adapter comes with or without camera mount. Camera mount for 14x14x5mm camera (Runcam Nano, Caddx...
cults3d
This goes to any 20x20 extrusion profile and is secured in position so it can't turn freely. The regular cutter that is sent with Creality printers (and must other like types) fit nicely. You can just let it slip into the clip, or press the grips...
thingiverse
This goes to any 20x20 extrusion profile and is secured in position so it can't turn freely. The regular cutter that is sent with Creality printers (and must other like types) fit nicely. You can just let it slip into the clip, or press the grips...
thingiverse
Simple and Effective Spool Holder for 20x20 mm aluminum frames
cults3d
A simple clamp for a gopro or other camera on a 20x20 frame. ...Suitable for shooting timelaps
thingiverse
You will need: * 8x 5x11x4 mm bearings * 4x M5 nuts * 4x M5x20 mm Allen bolts To mount it to the frame you can reuse the same bolts and T-nuts used in the original Creality spool holder (2x M5 T-nuts, 2x M5x10 Allen bolts) This part greatly...
thingiverse
Fits all laser engravers that have a 20x20 aluminum frame. The holes for the screws are 4mm and the nuts that fit the aluminum slot can be found here on Thingivers https://www.thingiverse.com/thing:1573410 -Feel free to press TIP DESIGNER ...
thingiverse
Here's my Skele7on frame for 20x20 stacks. It takes a Mamba Mini stack which is one of the bigger ESCs I've come across so I think it should work with most stacks while swinging 3" props carrying a Micro Eagle camera and staying in a small and light...
thingiverse
50 mm M4 screw and M4 nut is used to adjust spacing. M8 screw is used to mount 608 bearing. ...
cults3d
this was edited in tinkercad i editied the gpu pcie riser from ammarcoux and added the 20x20 mount and extended it from ixian made this to hold my 2 6600xt's on the back of the mining frame... ... the frame is a kingwin kc-8gpu that i got from...
thingiverse
this was edited in tinkercad i editied the gpu pcie riser from ammarcoux and added the 20x20 mount and extended it from ixian made this to hold my 2 6600xt's on the back of the mining frame... ... the frame is a kingwin kc-8gpu that i got from...
thingiverse
As a result you get a heavy, sturdy frame, that should kill all vibrations in an instand, plus some nice extras like the integratedadjustment wheels on the printbed. ... This build needs all the aftermarket and printed parts for the X-Y axis from the...
thingiverse
This is a cap for 20x20 aluminum frames. ... The PC case in the photo is an example of using this component.
thingiverse
This is a little mounting device for an ID retractor to mount it to your printer frame (CR-10, Ender 3 or similar) using an m5 bolt and a t-nut. The ID retractor will be attached to the front hook and will hold the cables out and back. ... Nice handy...
cults3d
This is a little mounting device for an ID retractor to mount it to your printer frame (CR-10, Ender 3 or similar) using an m5 bolt and a t-nut. The ID retractor will be attached to the front hook and will hold the cables out and back. ...Nice handy...
thingiverse
This is an adapter to mount a 20x20 ESC to your Blade Torrent 110 frame. Total height is 4.5mm and use M2 screws. The screws will self tap the holes but if you have M2 tap it is always better. With screw or tap, take your time, it will make a...
thingiverse
Made it for the Adimlab Gantry but should work on an 20x20 extruded Aluminum frame. Raise the Z axis high enough to slide this tool in. Turn off motors / printer. By hand, Adjust the Z axis down to rest on the tool by turning the threaded...
thingiverse
I design the Filament Guide for a Anet A6 Evolution cube type printer The guide for the filament is movably mounted It is printed together.
thingiverse
I design the Filament Guide for a Anet A6 Evolution cube type printer The guide for the filament is fix
prusaprinters
<p>I design the Filament Guide for a Anet A6 Evolution cube type printer<br/> The guide for the filament is fix</p> <h3> Print Settings</h3> <p><strong>Printer Brand:</strong></p> <p>Anet</p> <p><p class="detail-setting printer"><strong>Printer:...
prusaprinters
<p>I design the Filament Guide for a Anet A6 Evolution cube type printer<br/> The guide for the filament is movably mounted<br/> It is printed together.</p> <h3> Print Settings</h3> <p><strong>Printer Brand:</strong></p> <p>Anet</p> <p><p...
thingiverse
Usefull toolhoder for 3D-Printer which can be mounted on 20x20 Aluminium frame.
thingiverse
Hej fellow Makers! ... This is my design for a simple tool tray for 20x20 item frames. Enjoy! If you have an improvement proposal please leave a comment. Unfortunately necessary: No liability for damage to your device! ...Use at your own risk.
thingiverse
This is my design of a massive y-axis belt tensioner for a HICTOP 3DP-17 / ATHORBOT A01 Prusa i3-clone (it's identical) built with a single 20x20-ITEM-frame. You need one M6x30 with a hex head, a washer and a M6 nutscrew to adjust the tension of...
thingiverse
Designed for XY Core printer (CUBE) isnt allready but it mmust work. ... Desinged für einen XY Core Drucker (Würfel) ist nicht fertig Müsste funktioniern war Probe weise aufgebaut.
thingiverse
Internal Corner for 20x20 Extruded Aluminum Frame Forced insert but if need use holes to M4 no head screws Confirm your Extruded Frame with picture 5