21mm lens 3d models
23666 3d models found related to 21mm lens.cults3d
It is for 21mm lens diameter + 5.6mm lens height. How to support me? Do you like my things and do you want to support me? You can use these links if you want to buy something. This helps me doing more things. Thanks! ... Banggood: https://goo.gl/ZXgx3A...
myminifactory
It is for 21mm lens diameter + 5.6mm lens height. How to support me?Do you like my things and do you want to support me? You can use these links if you want to buy something. This helps me doing more things. Thanks! ... Banggood:...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=1060283 Instructions Customized version, works perfectly with Zeiss 21mm ZE lens, I just test it with a tilta follow focus and no slippage at all, good snug fit too. I printed it with 15% infill...
thingiverse
This was designed to replace a missing rear flare shield on a Zeiss Biogon 21mm f/4.5 wide angle lens. ... The tolerances are pretty tight so I had the one in the photo printed commercially in laser-sintered nylon.
thingiverse
Customized version of https://www.thingiverse.com/thing:47842 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=47842
thingiverse
Customized version of https://www.thingiverse.com/thing:47842 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=47842
thingiverse
Customized version of http://www.thingiverse.com/thing:44815 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=44815 Instructions Using the following options: cursor =...
thingiverse
A funnel to refill a bottle with citric acid granulate. ... Neck diameter ~21mm
thingiverse
... with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=69655 Instructions Using the following options: DualExtrusion = Extruder1 message = 21mm Font = write/Letters.dxf ToolOptions = 2 Nut_Size = 21 Tool_Length = 8 kerf = 0.4
thingiverse
... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=82067 Instructions Using the following options: Font = write/Letters.dxf $fs = 0.1 Nut_Size = 21 Tool_Length = 7 Tool_Height = 3 Has_holding_cap = 1 message = 21mm
thingiverse
... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=82067 Instructions Using the following options: Tool_Height = 3 $fs = 0.1 Has_holding_cap = 1 Font = write/Letters.dxf Tool_Length = 10 Nut_Size = 21 message = 21mm
thingiverse
Simple Thumbcuff 21mm inner Diameter, 2mm thick, 8mm long with M3 thread one side (probalby not enough to hold it for long, so a nut in addition is recommended) This is just a toy that you can use to cuff your thumbs together (or someone elses). ...I am...
cults3d
21mm Pegboard Holder. ...Pegboard part by my bestest buddy Angus!
thingiverse
21mm Pegboard Holder. ... Pegboard part by my bestest buddy Angus!
grabcad
Fully accurate model of the fpvcycle 21mm motor (https://fpvcycle.com/collections/motors/products/fpvcycle-21mm-motor-m3-m5-prop-shaft)With dimensions provided directly by the man himself, Bob Roogi. ...Separated into bell and stator for your...
thingiverse
This is a bearing block for 21mm round tubes. ...It uses four 8x22x7mm (608) bearings to make a firm and very smooth riding assembly.
thingiverse
This is a custom made lightsaber inspired by star wars. ...This time I went for a radius of 21mm so it fits better into a hand. ...I recomend to print the parts seperately.