230s 3d models

Landing Gear for Blade 230s

Landing gear replacement for the Blade 230S

made a vertical fin for the 230s that is more appealing. ...if printed with .6 top and bottom its actually lighter than the oem.

Hi, I created a windscreen wiper for a Blade 230s RC helicopter that fits nicely to the www.heli-scale-quality.com body for that kind of helicopter. ...Pictures and whole description about that nice helicopter can be found under...

replacement skids for the blade 230s helicopter and maybe other models Print Settings Printer: XYZ davinchi Rafts: No Supports: No Resolution: fine or excelent Infill: 35 to 50% Notes: the finer the print the better they are, and flip the part for...

This landing gear for the Blade 230s helicopter is angled at 2 degrees to make the tail sit about an inch higher than the stock landing gear. You'll need to print 2 "Brackets" and 2 "Skids". Print the brackets on their sides and use supports...

This is a replacement frame kit for the Blade 230S. You can still use the original electronics. 4 M2x10mm hex bolts and nuts are needed for clamping the tail boom. The nuts must be inserted\pressed in the right frame side. I printed all frame...

Blade 230s replacement skids. the skids are about 1g lighter and just as strong maybe stronger. I like to looks better. they are about 15mm wider and 2mm taller. they are a lot cheaper. $1.20 for the aluminium skid tubs. K&S 5/32 #8103. cut tube to...

i purchased a set of aluminium and carbon fiber skids from lynx for my 230s. I also purchased a replacement set of plates. got bored today so i created a block for the spare parts and bolted them to the other heli. looks good to me. ...complete kits...

This print is for the Blade 230s Helicopter but may work for others with the same type grommet and post canopy connectors. No modifications are required to the helicopter. Just remove the two rubber grommets from canopy and put them in the 3D...

I designed the landing gear for the Blade 230s V2. It is a perfect fit. I printed these gear in about 4 hours. My gear is printed from ABS but other material will work. There are 3 files. They include a Landing Gear mount bracket legs that will...

This is a simple and light replacement landing gear for the Blade 230S. It might look flimsy, but the goal is to make it fast to print and disposable. It can be used as replacement for the original landing gear or in conjunction with the replacement...

Blade 230s helicopter main rotor head linkage pair

Blade holder for the 230s. you will need to sand to fit for PLA. ...TPU simi-flex is no sanding needed.

Landing gear for Blade 230S V1 or V2. I crashed and designed these. Use some CA to glue the skids to the gear. I printed with no support and you can see the bridging effect on an Ender 3. ... Use support if you want to clean that up :)

Here's a part for the Blade 230s Helicopter. This is a pitch link for the swashplate to rotor head blade grip. If the link is too tight or too loose on the balls try scaling the print down or up a few fractions using whatever slicer you prefer.

Blade 230s tail motor mount and fin as one unit. Its a plastic copy of the microheli light weight unit. It is about 1.2g lighter than the microheli unit. Almost 3g lighter than the stock unit. This should help with the tail weight. 3g off a 10" lever...

Replacement vertical tail fin for the Blade 230s. Carbon fiber/ABS (stronger, cheaper, and lighter). holes need to be enlarged to 5/64. i will fix this in the next release. cut 2mm carbon fiber rod to length glue in place. you can strengthen the...

There are some Scale kits for the Blade 230s, which are very expensive but also extensive. But there are also simpler kits that are affordable. This is where the 3D printing comes in. Most parts can be made of PLA. Unfortunately I only have the...

a boom cut to the same size as the 230s part is 1 gram lighter. the 40mm cut off end can be made into a reamer for a perfect fitting jig. just cut teeth into one end with a file. then score the outside of the tube with a hobby knife. ...chuck it in a...

like this set of frame supports. it has 1.5mm flange around and fits into the hole 1.6mm supporting the full frame. the heli is tail heavy so adding weight where it's needed is not a prob. They just pop in with some glue. ...I hope you like.

hope u like it

Designed to fit into kingdallen's Canopy Quick Connect: https://www.thingiverse.com/thing:4617671

I broke my second boom on my E-Flite 230S V2. I have about 4 minutes of flight on the model. My landings were not hard. Each break was near where the tail boom enters the body. After I filled off the broken portion of the boom (about 3 CM),...

this is a swash level tool for a blade 230 s helicopter, and maybe others Print Settings Resolution: fine Infill: ...

Remixed the original to make both sides equal in size, and without the hole as i'm using XT60. ... This one has a small gap on the left side to allow battery connector wires to exit.

Remixed the original to make both sides equal in size, and without the hole as i'm using XT60.

I always break the front frame mounting point for the landing gear. The frame is cheap to replace, but it is a lot of work. So I designed this very simple part, that can be glued or screwed in place as a simple fix. ... The pictures show the part...

blade 230s and 250cfx upper links

** UPDATED: Use the new GoPro Skid Mount for Blade 230S v6.stl file with new wire tie slots and more reinforcement on the GoPro mount section ** I fly RC Helicopters, and also like to take in-flight video footage. Couldn't find a GoPro mount for...