240z dome light 3d models
217952 3d models found related to 240z dome light.thingiverse
This is a redesigned Dome light for a 1971 Datsun 240z. It fits the same as the stock part but is designed to have 3 small led strips wired into it. ... I printed it in HIPS and used a small piece of acrylic as the lens.
grabcad
My map light bezel was broken on my old z, so I decided I would try and print a new one. This fit very well on my car and this is my latest revision. ...I also have a version with my logo, but I assumed no one would be interested in that.
thingiverse
This is a redesigned part for a 1971 datsun 240z. ... It fits the same as the stock part but is designed to take a small strip of 12v leds.
thingiverse
Dome Light useful for those trunk that not have one, or rear seats Simply connect from the front light
grabcad
Light dome I made when my "better half" washed a glass dome and it shattered .CAUTION. ...You have to use LED bulbs, other vice it melts and might burn.
cults3d
Light dome it is an experiment of gears and it works to project light on the wall, this light it is filtrate by another board with perforation allowing the light cross the material, and projecting itself on the respective perforated drawing on the...
thingiverse
I used clear PLA to print dome and used 18650 batteries x3 to power 12v 5050 Cree strip LEDs.
thingiverse
I designed this piece for a friend with a 1973 Datsun 240z.The Map light located above the air controls in the center console/dash. This Is used with the push-to-click style map light. You may need to cleanup the edges for best fitment, and...
thingiverse
Hollowed Dome Light that I have created for replica of Masuyama Giant Robot
thingiverse
This is a dome light model I created with what was left from the dome light on my 88 Merkur XR4ti. It should fit tight, but well. ...I have used ninjatek Armadillo with good success.
thingiverse
For SoundOff 6" Dome light installation. ... Speeds up the install time and makes it easier to get a clean install.
thingiverse
VW Beetle dome light. Take care when re-assembling the light. Recommend using LED rather than normal incandescent globe. ... Printed in ABS.
thingiverse
Broke my dome light cover and decided to design a new one based on the broken peices insteasd of purchasing a standard cover.
thingiverse
A dome pathway light for outdoor lighting. Can be mounted with a 1/2" EMT pipe. See the video on the build process. ... https://www.youtube.com/watch?v=uInJrb_ljtM
thingiverse
This clip allows a Big Larry (NEBO) or Quantum (Harbor Freight) inspection light to be used as a dome light. The thing holds the light to a 1.85" roll bar like that of my CanAm X3. The light can easily be removed when needed for other uses. It keeps...
thingiverse
A remix of the previous dome light. If you want to remove the XR4Ti logo, just load it into tinkercad or what have you and blank it out, or add your own logo. Print this in ABS, so it will survive your car interior. Or polycarbonate. ABS smoothing...
prusaprinters
That’s pretty nifty, because now we just need make a single, small part 60 times and can assemble a full globe.This is basically a model of one of the geodesic domes by Bucky Fuller, the Fly’s Eye Dome. It’s a geodesic dome with circular holes, made...
thingiverse
This is a reproduction dome light is for a 1958 Edsel. More specifically, this one came from a 58 Edsel Pacer. It was printed in white to match the roof color, but you can choose any color. I used ABS for the frame, but you may also consider PLA.
prusaprinters
If using PLA, be sure to change the light to LED and keep the car out of extreme temperatures to avoid warping (122F or above). You may use a hot poker to create holes in the clear dome for the screws. I used new small self-drilling screws from my...
thingiverse
Reduced the size of the original dome by seitse - so it can print on my Prusa Mini Original: https://www.thingiverse.com/thing:4142787
cgtrader
Dome Light by Moooi | 3d model produced by Design Connected | www.designconnected.com This 3d model is part of the highly acclaimed Design Connected collection featuring 6500+ carefully picked exclusive furnishings. Check out our full range of 3d...
cgtrader
Name: DOME Version: 2013 Preview: No Units: Millimeters Dimension: 432.6 x 184.92 x 513.82 Polys: 29 886 XForm: No Box Trick: No Model Parts: 19 Render: V-Ray Formats: 3Ds Max 2013, OBJ, FBX, 3DS
prusaprinters
Reduced the size of the original dome by seitse - so it can print on my Prusa MiniOriginal: https://www.thingiverse.com/thing:4142787 Print SettingsPrinter Brand:PrusaPrinter: Prusa...