26650 battery holder 3d models
384192 3d models found related to 26650 battery holder.thingiverse
this is my design of a 26650 battery holder using 3m standoffs . each battery needs 3 stand offs of any size really i used 6mm long 2 with threads on the end and 1 that has a threw hole to thread into both sides. you can make the holder any size by...
thingiverse
4x4 26650 connectable battery holder. I generally use PLA+ and it provides enough strength to connect 4-6 holders together. You may then wire your batteries into whatever combination of s and p you need. You may also wire then as 1sXp to create...
thingiverse
A 26650 battery holder with an attached holder for a 1" x 3" circuit board
thingiverse
I holds a single 26650 battery. It has cutouts for rubber bands to hold the battery firmly in place but they are not needed. It snaps to its self so it doesnt need glue. to make the contacts you can tape a little piece of alu-tape on the ends.
thingiverse
This part holds 26650 lithium cells in a 2x3 cell square configuration. Use two per battery pack/module, one piece near the top and bottom. The hole diameter is 26.65mm which is slightly snug for my K2 LFP cells with a paper wrapper. I use...
thingiverse
After a close call between a 40A battery and my car-keys burning a hole in my chest pocket I made this in Fusion 360 to keep me from further nippleburns or exploding batteries.
myminifactory
I started building battery pack with some 26550 LiFePO4 and I didn't want to use hot glue to connect the cells so I designed this spacer with minimal space between cells.
thingiverse
... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=140931 Instructions Using the following options: thickness = 2 curve = 6 custom_length = 65 battrery_type = Custom batteries = 6 margin = 1 custom_dia = 27
thingiverse
... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=140931 Instructions Using the following options: batteries = 8 curve = 6 thickness = 2 battrery_type = Custom margin = 1 custom_dia = 27 custom_length = 65
thingiverse
26650 battery holder for power pack / power wall. ... This is only a prototype.
thingiverse
This is a 4s4p battery pack 26650 holder with teeth to mount it to another one and without teeth.I have designed this to hold 26650 liitokala batteries and fit my eeb ebike.
thingiverse
26650 Battery holder for two batteries the screws are there to tension the connections, to make a better contact
thingiverse
This is a holder/sled for 2 26650 battery, these are to be used with keystone contacts #209 and #228
thingiverse
Customized version of http://www.thingiverse.com/thing:57281 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=57281 Instructions Using the following options: _walls =...
thingiverse
Customized version of http://www.thingiverse.com/thing:57281 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=57281 Instructions Using the following options: _walls =...
thingiverse
26650 pack design I Just bought 200 LIFEPO4 26650 and needed something to make battery packs. use nickel tape, thread through the slots so they act as contact springs. configure all in parallel or series or a combination. no supports needed.
thingiverse
Customized version of https://www.thingiverse.com/thing:2821012 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2821012
thingiverse
26650 battery pack. 2S, 3S, 4S, 5S and 6S designs. Works best with spot welded tabs. The cap is a tight fit so that it can be glued on. The hole through the middle will fit a 1/4" or 6mm bolt to allow it to be bolted to something. The battery pack...
thingiverse
Customized version of http://www.thingiverse.com/thing:48235 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=48235 Instructions Using the following options: _height =...
thingiverse
I am building a li-ion 10S10P battery with 26650 type cells, so I share this battery holder (a prototype, the last version is much more advanced) if anyone finds it of interest. The gap between plastic and batteries is 0,3 mm. ...in radium.
thingiverse
u can add + - signs to the print as needed Needed: 20, 18 or 16gauge solid copper wire or any wire you can make a spring or pin for contacts use a 10 to 15% fill when printing it will still need to flex to remove battery from holder if you print on...
thingiverse
Холдер под батарейки 26650 Делал для вейпа под аллюминиевый корпус
thingiverse
Battery Holder for 26650 batteries in quad and hex configuration designed to use these clips http://dripp3d.com/positive-negative-battery-contacts-5-pair-pack/ or...