2gt belt clamp 3d models
79708 3d models found related to 2gt belt clamp.thingiverse
I needed to clamp a GT2 / 2GT belt for a custom SCARA design, with some tight spots. Most clamps don't run past a sprocket, or tend to slip if they do. I was inspired by Idegraf's design (https://www.thingiverse.com/thing:1247615), but needed...
thingiverse
designed to mesh with GT2 6mm Timing belts, It allows you make a loop in the belt.
prusaprinters
I was looking for a very simple 2GT belt clip and couldn't find anything that didn't require additional hardware for an open belt so I came up with this simple design. It features two individual parts that join together to lock the end of the belt in...
thingiverse
A small belt clamp, suited for a GT2/2GT belt it's a tight fit (2.1mm gap) but once on it will not move. I suggest adding a cable tie as shown. I opted for 99% infill as you need it to be solid so it doesn't break, as for resolution I don't think...
thingiverse
This is a belt clip/clamp for a steel reinforced white polyurethane 2GT belt. The white belt is thicker than a regular rubber 2GT belt, so if printed as is will be too loose for rubber belts. Tapered 0.5 degrees and filleted at the top for easier...
thingiverse
This belt sleeve is designed to be used with belts that, when overlapped with teeth interlocked, are 2.2mm thick.
thingiverse
Belt tensioner Print Settings Printer: Zonestar 3D P802M Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.1 Infill: 20%
thingiverse
I'm currently experimenting with printing my own timing belts using flexible printing material. I'm currently using TPU. Here is a Fusion 360 file I am using to generate my tests from. You can specify the number of teeth and the width of the...
myminifactory
2GT belt clamp for the X-axis, fit for the standard plate of the Flsun Cube. In two variants -V1 - & - V2- and the old versions, without square recess. For variants without a square recess, it is necessary to use flatter nuts. Screw hole diameter:...
pinshape
2GT belt clamp for the X-axis, fit for the standard plate of the Flsun Cube. In two variants -V1 - & - V2- and the old versions, without square recess. For variants without a square recess, it is necessary to use flatter nuts. Screw hole...
thingiverse
This is originally made for my RK 3D printer: https://www.thingiverse.com/thing:2537454 A very small 2GT Belt tensioner/mount/holder/lock for any purpose, two versions depends on the belt teeth side. They take m3 nuts from both sides (If needed) and...
pinshape
2GT belt clamps for the Y-axis, Fits to replace the standard holder. In two sizes, one for neoprene with fiberglass core and for PU (polyurethane) with steel mesh. With opening for pushing out the M3 nut and for 2GT strap itself. With the...
myminifactory
2GT belt clamps for the Y-axis, Fits to replace the standard holder. In two sizes, one for neoprene with fiberglass core and for PU (polyurethane) with steel mesh. With opening for pushing out the M3 nut and for 2GT strap itself. With the size of the...
cgtrader
2GT belt clamp for the X-axis, fit for the standard plate of the Flsun Cube. In two variants -V1 - & - V2- and the old versions, without square recess. For variants without a square recess, it is necessary to use flatter nuts. Screw hole diameter:...
thingiverse
This is for 6mm width belt Updated 2020/04/20 Bearing_Block_M3_16mm_01.stl is the new one. I fixed the counter bore dimension for nut. You need M3x16mm screw and nut. No need to add support but I suggest to use brim. ... Old design info M3x20mm...
thingiverse
2GT belt clamps for the Y-axis, Fits to replace the standard holder. In two sizes, one for neoprene with fiberglass core and for PU (polyurethane) with steel mesh. With opening for pushing out the M3 nut and for 2GT strap itself. With the size...
cults3d
2GT belt clamps for the Y-axis, Fits to replace the standard holder. In two sizes, one for neoprene with fiberglass core and for PU (polyurethane) with steel mesh. With opening for pushing out the M3 nut and for 2GT strap itself. With the size of...
cgtrader
2GT belt clamps for the Y-axis, Fits to replace the standard holder. In two sizes, one for neoprene with fiberglass core and for PU (polyurethane) with steel mesh. With opening for pushing out the M3 nut and for 2GT strap itself. With the size of...
thingiverse
Print 2 per axis. ...Meant for the 10mm wide 6mm belt real 2GT from e3d
thingiverse
2GT belt clamp for the X-axis, fit for the standard plate of the Flsun Cube. In two variants -V1 - & - V2- and the old versions, without square recess. For variants without a square recess, it is necessary to use flatter nuts. Screw hole...
cults3d
2GT belt clamp for the X-axis, fit for the standard plate of the Flsun Cube. In two variants -V1 - & - V2- and the old versions, without square recess. For variants without a square recess, it is necessary to use flatter nuts. Screw hole diameter:...
thingiverse
... on the sides. I wanted to stop buying the custom sized replacement belts and picked up a 10 meter long 2GT belt and can now just cut that to size and ziptie these to each end to replace any length belt that breaks from overtightening/general wear.
thingiverse
... ...I didn't want to spend more money on a weapon belt that could break easily or just not fit at all so I took this as a challenge to boot up Inventor and try to CAD a timing belt I could actually use in competition. ... Use TPU for best results.
pinshape
2GT belt pully mount to NSK 6202Z fixed with M4 screw
grabcad
The corner braces for belt clamp systems. ...They are designed for assembling picture frames, drawers, chair frames or other articles of various sizes and configurations prior to glueing or fixing.
thingiverse
This is a belt clamp for RepRap less than standard. This is a part of my Y carriage for RepRap. ...Look here http://www.thingiverse.com/thing:779890 If you need this model with nuts holder look here http://www.thingiverse.com/thing:779919
cults3d
Wonderful design by LiViS! ... I wish I had found these months ago. I noticed on my Flying Bear they were close to the bottom belt so I didn't want them to rub. ... I radiased the corners to prevent them from touching.