2kg filament 3d models
172858 3d models found related to 2kg filament.thingiverse
Super simple Design for a filament spool holder, which can hold rolls from 500g up to 2kg. The wheels are split up into 2 parts to allow for supportless-prints. ... Just glue them together.
thingiverse
Ich verwende häufih Filament auf 2kg Rollen Da ist der Standart-Rollenhalter von Vyper nicht passend. Aus diesem grunde habe ich mir diese drei unterschiedlichen Varianten gefertigt. ...Es wird benötigt: 1x Gewindestange M8 2x Hutmutter M8 1x...
thingiverse
This is simple holder for 2kg spool 300mm diameter x 100mm width. ...Post-Printing Assemble with four M5 screws
thingiverse
Spool holder that can fit up to 2kg fillament spool. The shaft is 18cm long. Diameter of the bolt is 30mm, the nuts are 20mm diameter and the thread is 1.5mm. Please note that you will need two nuts to attach the sharf to the holder. On my photo...
thingiverse
Filament Halter für Große Rollen Für die v2 rolle werden 5x10x3 kugellager benötigt ( hrc1224 10pcs)
thingiverse
A big spool of filament wont fit on the original piece beacuse of its width? - Well this guy solved the problem https://www.thingiverse.com/thing:4014054. I decided to go with a full thread and square shaped nuts for a snuggle fit, made it...
thingiverse
Shaft is modified to be printed vertically, holder is higher and wider.
thingiverse
Increased by 30mm to carry large filament rolls up to 2kg and more. Can hold up spools upp to 30cm outside diameter and 12cm width ( lenght variable ) Attention my printer hsa some squash ball feet installed which increase the maximum height ...
thingiverse
This spool holder uses a bit of a standard 40mm PVC waste pipe. ...Print the two sides of the holder and cut a bit of pipe of a desired length. Choice of filament does not matter. ...I used PLA.
thingiverse
By having an excess of M8 and M6 Threaded rods and few gear bearing laying around I decided to make them hold big spool of filament. ... --------------------- You need : 1 pcs - m6x250mm 2 pcs - m8x165mm 4 pcs - m8x200 8 pcs - m8 nut +10 pcs -...
thingiverse
Height Extender for my Wanhao i3 to mount 2kg Filament spools. ... You need: 4 x M5x20 2x M5 hexagon nut
prusaprinters
<p>The Drybox is a remix and recreation of above models. It is build to fit directly on top of the Prusa MK3S+ Printer and has a shaft to hold the spool, so no need for any bearings and other tubes.</p><p> </p><p>To attach everything you will...
thingiverse
Solid, free-standing, holder for 2 kg of filament rolls. Dedicated to the PlastSpaw R150x100mm roll. ... Made from one piece, it requires a printer with a large working area (height 250mm).
thingiverse
With this new mount, you can use 2KG filament rolls on a Ender Printer. ...I use ist on my Ender 3
grabcad
One empty filament roll for 2kg 3D printing filament (PLA, ABS, PET, PETG etc.)
cults3d
This remix of the Filament Duck enables it's use with colorFabb's 2.2kg XL spools. ...We printed this model in our Economy PLA, which is supplied on the 2,2kg spools that this model is made for.
thingiverse
This remix of the Filament Duck enables it's use with colorFabb's 2.2kg XL spools. We printed this model in our Economy PLA, which is supplied on the 2,2kg spools that this model is made for. Also take a look at our remix to fit the colorFabb 750gr.
prusaprinters
We printed this model in our Economy PLA, which is supplied on the 2,2kg spools that this model is made for.Also take a look at our remix to fit the colorFabb 750gr. ...spools: thing:1862680And our 4.5kg spool holder here: thing:4079857This is a remix...
myminifactory
I designed a quick and simple 2KG spool holder that doesn't need any additional parts or assembly--just put the bar through the spool, and then seat the bar on the arms of the holder. Then sit on a flat surface. Super simple Holds spools up to 21cm...
thingiverse
Filament Clip designed to fit on a 2kg spool from Material4Prints. They have a lip on the outside, where the clip will snap onto. ... I printed mine with a brim with 0.4mm distance to prevent warping
thingiverse
this thing might warp at the pointy corners up top so make shure yout print sticks propperly. ... https://www.youtube.com/watch?v=y-WnSGS6wDw
thingiverse
Stock screws...down stickers nozzle not blow up!
thingiverse
This is a very simple but reliable filament holder for prusa i3, makerbot spools. I know this is pretty specific, but I thought I would at least share the idea so others can make their own for their particular spools. Notes: Ultra-fast spool...
prusaprinters
<p>The "axe" part is the same for the 2 supports V1 and V2.</p><p> </p><p>La pièce "axe" est la même pour les 2 supports V1 et V2.</p>
thingiverse
Universal filament coil holder with threaded closure. For bearing 8mm. With a length of 140mm for coils up to 2kg. On the knob, the resistance can be adjusted so that the coil rolls off steamed easily. See also:...
thingiverse
As the filament spools of ColorFabb PLA Economy didn't fit onto my standard spool holder, I modified the Freestanding Filament Holder by voltivo to suite them. Width is 120mm now. Spool diameter is approx. 30cm now. ... Additionally I added screws...
thingiverse
UPDATE (June 27, 2022) ==================== The shallower spool holder was used to generate a longer part, accommodating spolls of 2.2kg. Thank you Brad5610 for providing the idea and dimensions! Part description ==================== The spool...
thingiverse
It combines both units (feeder, sensor) into one which can be sled along the profile so that the filament path is tangent to the spool. It also leaves space for larger spools such as the 2 kg spool in the picture. What you need: 2x18 mm M5...