2s lipo and charger 3d models
2297960 3d models found related to 2s lipo and charger.thingiverse
2S LIPO Balance / Charger Plug Puller "JST-XH" type sorry, https://www.thingiverse.com/lgbell, your logo was too hard to put back on the handle all i did was change the width of the clip and i added some triangles to make the connection to the handle...
thingiverse
Parallel / Serial 2S LiPo Board This board is designed to lay 3 2S batteries in parallel or in series (depending on the wiring).
thingiverse
I noticed the JHEMCU RuiBet 1-2S LiPo charger runs a bit warm so I designed this fan mod to provide active cooling. You will need a 5v 2507 fan to create this. Print in PETG or PLA Instructions: - Remove the bottom plate of the JHEMCU charger. This...
thingiverse
It's been scaled like 101-102% and the hole removed and a battery holder added for the HobbyKing turnigy 2s 1800mah lipo. To power a crossfire module on the ix12. I added some foam to the backside near the center to keep the tab tight against...
thingiverse
This is a stacked Battery-Case for a 2S and 3S Lipo. ...According on your needs, you can print the cases as independent 2S and 3S Cases or as a stacked Box where the 2S Case is on the cap of the 3S-Case.
thingiverse
Tired of your batteries laying in a tangled mess when charging them. ... I created this box to hold the charger, the balance board and the batteries keeping them all in place and secure while charging. ...
thingiverse
This Mobula7 battery holder supports both Nano-Tech 1s 600mah and 2s 260mah battery. * This fits between the 2 battery holder bars in the frame; please slide the larger side in first follow by pushing the smaller side in * 2 battery sizes in one...
thingiverse
2s lipo mount that fits any frame with 16x16 fc mounting. ...When used on the Wee-Mix nuts are not necessary when fitting screw through frame first
thingiverse
This is for Calimero frame to attach 2S lipo 450mAH. It's tight fit to the hole on the frame. ... Print with flexible filament and no need support.
thingiverse
Clip to prevent 2s Lipo battery from falling out of goggle strap on fatshark goggles. ... Fits best with GNB 2s 3000mAh Lipo.
thingiverse
This item Holds the BETAFPV 1S lipo battery charger with storage for both charged and uncharged batteries and a few spots for misc items. Charger has a nice snug fit and will not fall out of holder. V2 was added V2 has .20mm smaller (12.2mm x...
thingiverse
Immediate insight into your LiPo battery status. Wiring towards "Full", the battery is full. Wiring towards "Empty", the battery is empty. ... Length = 32 mm Width = 14 mm CaseHeight = 44 mm Designed for "Perimeters only" printing.
thingiverse
Immediate insight into your LiPo battery status. Wiring towards "Full", the battery is full. Wiring towards "Empty", the battery is empty. ... Length = 30 mm Width = 10,5 mm CaseHeight = 45 mm Designed for "Perimeters only" printing.
thingiverse
Immediate insight into your LiPo battery status. Wiring towards "Full", the battery is full. Wiring towards "Empty", the battery is empty. ... Length = 17 mm Width = 13 mm CaseHeight = 37 mm Designed for "Perimeters only" printing.
prusaprinters
Immediate insight into your LiPo battery status.Wiring towards "Full", the battery is full. ...Wiring towards "Empty", the battery is empty.</p><p>Length = 30 mm<br>Width = 10,5 mm<br>CaseHeight = 45 mm</p><p>Designed for "Perimeters only"...
thingiverse
To complete this LiPo charger you will need: A couple of battery pins: A TPS4056 Module An integrated voltmeter Tools like solder iron, hot glue ecc...
thingiverse
I got a lipo and a charger lying around, being used to charge stuff (really?), so I designed a case to have everything together and make the whole thing durable. Just use a couple of m3x10 screws to hold both sides of the case together. BOM:...
thingiverse
this is a servo holder for a wltoys a959 servo and a battery tray for a wltoys a959 2s lipo