3 4 knockout plug 3d models

... box or panel. Designed in Fusion360 using the NEMA Conduit Fitting specification so it should fit most any typical electrical box with 3/4 conduit knockouts. ... I also have 1/2 version as well in My Things along with other useful garage stuff

Hydraulic Fittings - Female Plug 3/4"

3/4 inch plug. Top is domed. ...Print Settings Supports: Yes

Plug I made for 3/4″ thin walled EMT for my MPCNC project. ...I wanted to run wires through the tubes without fear of sharp edges.

Great make, the original post has the wrong size for the 3/4" plug in the .stl and the scad file. ...&nbsp;It's also missing the threads.scad file required for the compile.</p><p>The picture shows the original size (smaller) and this one.</p>

3/4" three quarter inch plug for poly irrigation pipe. Instructions The hardware store didn't have one, and I said, "Duah! I have a makerbot!" In less time than it took to go to the store, I modeled...

Rival Knockout Barrel: Test of dimensions

Plug Roscável 3/4"

Customized version of https://www.thingiverse.com/thing:3204763 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3204763

3/4 plug 20*27 pipe

This is a basic 3/4 inch BSP tap plug. ...I made a couple of different threads for around the house and in the garden all work well

Simple Plug for Gardena's old 3/4" pipeline system.My old plug was leaking so I created this to replace the old one. Should be printed with a tough material since some pumps can build up quite some pressure. I used Filamentum ASA since my plug will...

I needed a 3/4 inch NPT plastic pipe plug to seal a pipe. It may not be an exact fit but it worked when printed in ABS plastic for my needs. Most NPT threads are tapered so that the plug or pipe gets tighter the more you screw it in. These are...

... and keep stuff out of your junction box or panel. Designed in Fusion360 using the NEMA Conduit Fitting specification so it should fit most any typical electrical box with 1/2 conduit knockouts. I will also be posting a 3/4 version as well. ...

Plug for Marui HI capa 4.3

I recently converted my Hobie kayak to use the "Hobie Twist Lock Seat Conversion Kit" - https://is.gd/wEzcjg I had to order the3/4-Inch 10 High Carbon Steel Machine Screw Plug Tap Link: http://a.co/9zYbi2y Which I did not have a large enough tap...

I recently converted my Hobie kayak to use the "Hobie Twist Lock Seat Conversion Kit" - https://amzn.to/3gLe7EV I had to order the3/4-Inch 10 High Carbon Steel Machine Screw Plug Tap https://amzn.to/2YUhbs6 I did not have a large enough tap handle...

This is a remix to add a larger thumbwheel to a 3/4 NPT plug to match the plugs for my Fat Sac ballast bags. The gap between the threads and the cap/knob is for an O ring but it works without the O ring well enough for my application Additionally...

... supposed to cover up the exits not in use. ...Of course, I lost those covers long ago. So I took one of the finely modeled 3/4" BSP threads, and added a fixed cap in Blender. ... Also works great to seal off leaking outlets of 4-way splitter valves.

I needed some extra plugs for the ballast bags in my boat on short notice so I designed some up quick and printed them. There's a spot at the bottom of the plug for an o-ring. I used a 23MM ID x 3MM thick one I had laying around. ... Printed in PLA,...

This Model was build using OpenSCAD, it's a plastic stopper male 3/4 inch diameter the thread need an anti-leak tape or epoxy paste to use it, if you print that model in 3D please tell me in the comment if the thread work well and not left liquid...

This Model was build using OpenSCAD, it's a plastic stopper male 3/4 inch diameter the thread need an anti-leak tape or epoxy paste to use it, if you print that model in 3D please tell me in the comment if the thread work well and not left liquid...

... bracket for an early 1900's gas lamp and I am trying to match the illustration I found of it. ... Made this pipe plug to match the decorative end caps in the picture. ... Threads were are a little too tight at 100% scale, fits perfectly at 98%.

This works for any 3/4" / 19mm hole in sheet metal. I printed this example in 3DXTech polycarbonate but most other materials should be fine. This is for the named size hole, not for covering a hole made for conduit or pipe with that size ID, the...

End caps I designed for 3/4" EMT conduit which I used for the spool holder rod in my filament dry box. They help protect the wall of the box from being scratched by the end of the rod. Even though you can't see them when assembled, I thought they...

Customized version of https://www.thingiverse.com/thing:1943463 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1943463

Customized version of https://www.thingiverse.com/thing:3495576 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3495576

Customized version of https://www.thingiverse.com/thing:1943463 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1943463

Customized version of http://www.thingiverse.com/thing:44815 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=44815 Instructions Using the following options: type = 1...

Customized version of http://www.thingiverse.com/thing:193647 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=193647 Instructions Using the following options:...