3 5 hdd brackets for q500l case by 3d models

Holder for Raspberry Pi in a 3.5" HDD bay

Plain and simple 2.5" HDD hinged case. Case will fit HDD with side mounting screws. Stick to print guidelines and it should match nicely. ... Hinges might require a bit of strength to assembly, as they are designed for tight fit, but this...

NAS case for two 3.5" HDD and Intel NUC. There is enough space inside for 4x 18650. ...

Hello, I designed a case for my Odroid XU4Q so it can hold a 40x40mm fan as well as a 2.5 inch HDD. You will need -4 M3*6 or M3*8 screws to close the case -4 M3*6 screws to fix the fan -1 USB cable to SATA to connect the HDD to the Odroid The TPU...

My specific use case is to add a 2nd HDD mount in the N-ATX v2 case which only has 1 3.5" HDD mount. One file has mount for a 60mm fan, the other does not. Unlike the above build, you cannot print 20 of these and continuously stack them, you would...

A box for up to 3 3.5 disks, which can be used as independently standing or embeded in a Desktop (tested on  the Mini-ITX station). There are 8 screw holes for every HDD (4 on the bottom and 4 on the side). Dimensions were tested on Seagate Barracuda...

This is a holder for the Raspberry Pi for mounting on the side of a 3.5 HDD as you can see on one of the renderings. Designed for 3D printing.RPi model on image is from Hasanain Shuja. ...(Raspberry Pi 4 Model B).Created with Fusion 360.

This is a holder for the Raspberry Pi for mounting on the side of a 3.5 HDD as you can see on one of the renderings. Designed for 3D printing.RPi model on image is from Hasanain Shuja. ...(Raspberry Pi 4 Model B).Created with Fusion 360.

# 3D printed enclosure for 2.5 drives * Thick file - for 9.5mm drive thickness * Slim file - for 7mm drive thickness

My first design of a sata/ssd case, to use with GD-IDE mod (thanks to DragonCity). ... Suggestions are welcome !

To take full advantage of this feature, a 3.5" HDD Slide-In Module has been designed specifically for this case. This module can be installed in conjunction with the main board, providing additional storage options. To get started, head over to...

Thats the specs for 3.5" Drives. If your printer does not print accurate or your filament shrink a lil bit, print it with 101-103% on the X/Y! For me, with 100%, the drives fits absolute perfect with zero gaps. But that will only work with a...

Couldn't find a HDD bracket for the DL380 so I made my own, taking the faceplate from a similar design which I've lost the link to. Supports work best as tree, easier to remove. ... This should work with most HP series 2U rackmount servers that take...

This is remix of a Case for a NAS Build with the Odroid H2/2+/3/3+ BoardsI added new HDD rails with vibration dampening.The rails consist of two partsthe rail shell is of PLA/PETGthe rail inserts are TPUThere are two different railslong railshortend...

I needed a third HDD bay, so I came up with this simple stand/enclosure to keep either next to or inside my computer case. I haven't printed it yet, but plan on doing so this week. *UPDATE 8/11/19* The first print didn't work out due to...

Simple enclosure to make long term HDD storage a bit safer. ...There may be not enough ventilation to have the hdd running in it. Photos show it printed with Prusament PLA Galaxy Black.

I possess several boxes of 3.5-inch hard drives from the brand Orico, they are designed for stackable use. ...But since they are stored in a drawer, I created a support so that they hold up without any problems.

This support in for an Open Frame Computer PC Case Chassis for ITX

...Facing difficulties with 5.25" to 3.5" adapters, I designed my own minimalistic mount. However, I didn't complete it; instead, I created slides for the intended hard drive bay. I searched online for similar designs but couldn't find one that worked.

This accessory is intended for use with any 120mm case fan, allowing it to be securely fastened to the front of the Cooler Master Masterbox Q300L PC case. By adding 10mm of clearance between the fan and the steel panel, it significantly reduces noise...

The Odroid H2 and the Odroid H2+ are some of the few single board computers which offer PC like interfaces including 2x SATA, an NVMe slot, 2x 2.5 GBit ethernet (1 GBit for the H2) as well as dual RAM sockets. Besides the interfaces the board is...

8 × HDD 3.5 cage for 5 × 5.25 slot For powering the fan, I used a three-pin dupont plug and connected + to the middle pin. ... Caddy strips: https://www.thingiverse.com/thing:4696379

Credits for the 3D Mean Well LRS Model https://grabcad.com/library/lrs-75-mean-well-1 20.06.2019 Adaptation of my Odroid XU4 NAS case for the new Odroid N2. Slight modifications (more clearance) to make the two case parts less "snappy". Required...

... Credits for the 3D Mean Well LRS Model https://grabcad.com/library/lrs-75-mean-well-1 20.06.2019 Adaptation of my Odroid XU4 NAS case for the new Odroid N2. Slight modifications (more clearance) are made to make the two case parts less "snappy".

ideal form a picture on facebook, so i design this case All parts are separate objects Fully ready to 3D Printing Clean and non-overlapping topology Each part has a STL File This means 6 STL files Model is settled to 0,0,0 XYZ Axis Make the right...

Thermaltake Suppressor PC chassis features a total of six mounting points for 3.5'' HDDs, but only comes with three brackets. You can hang up to three HDDs vertically behind the backplate, and put up to three horizontally in the bottom 3.5'' frame,...

3.5 in hdd

This is a custom mix of https://www.thingiverse.com/thing:1704615. ... CoolerMaster Dual SSD Tray for 3.5" Hard Drive Bay Version 1 Features a Tighter Fit for Your SSDs

An 3,5' HDD Box for Hard Disk Drives

# 3D printed 2.5" HDD Enclosure # Summary A simple 3D printed case for an old 2.5" HDD. The case is designed such that, for the most part, it is a push-fit, with four nuts at the bottom, mounting the drive to the plastic case. ... # Links The adapter...