3 5 inch hdd 3d models
1086673 3d models found related to 3 5 inch hdd.thingiverse
Attach the bracket to a 3.5 inch HDD using #6-32 screws (generally standard for 3.5" drives) and slot it in place on the retaining rails. The easiest way is to flip the bracket and drive on it's top and the screw holes and bracket should line up. A...
thingiverse
Stand for two 3.5 inch hard drives. For my home RAID system. ...Printed 4 at once.
cults3d
Stand for two 3.5 inch hard drives. For my home RAID system. ...Printed 4 at once.
prusaprinters
Simple HDD case for storage/traveling, with a tongue to keep the HDD in place.Print both parts and glue them together
thingiverse
This storage solution (pun intended) holds seven 3.5 inch hard drives at a time. Your infill percentage and pattern should reflect the kinds of drives you plan to store - 1TB WD Blues from 2016 on aren't very weighty, so you could get away with...
thingiverse
Just a simple 3.5 inch hdd holder with m4 mount screw supports both thicc and slim 3.5 inch drives hdd pcb mounts outside to help with cooling (my drives dies cause the pcb overheats) to be used with the flat mount i made (...
thingiverse
Materials: x4 3.5 inch hdd screws [reuse] x2 original screws from the 2.5 inch hdd caddy [optional] x2 power supply screws Notes: When mounting, pay close attention to the front/top inside of the case where the front IO pcb is, make sure to not...
thingiverse
... required for this mod: 1. A 92mm x 14mm pwn fan to replace the original 92mm x 25mm rear fan. There is not enough room for a 3.5 inch hdd in NZXT H1v2 with the original rear fan. 2. 4 x 6-32 nuts. ...I do not trust tapping on the printed object.
thingiverse
This set of 3.5" HDD Rails is a remix adapted for use with a Micro Center PowerSpec G429 chassis. I started with the HDD Rail design by Punday (thank you muchly) and then changed just about every possible dimension, moved the holes around and added...
thingiverse
This mount will let you put a 3.5 inch Desktop Hard Drive where your 360's DVD drive used to be. It's designed to be cut with a CNC router, but you could probably print it just fine. Instructions I cut the mount out of 1/4 inch PVC on a CNC...
thingiverse
This is adapter tray to fit 2.5" SSDs into a 3.5" HDD mount. There are four versions of this model; two that fit 3x 7mm high SSD and two that will fit 2x 8mm+ SSDs. ...For each mount there's a full sized 3.5" tray and a "stubby" tray that's only 101mm...
thingiverse
Printing does not require supports. ... Hardware: metric M3 or imperial 6-32 screws
thingiverse
Also increased the height so that it is about the same height as a 3.5" disk, making it slide in a little easier which also aids in port alignment. Tested with a ProBox HF7. I get good alignment on the first try about 70% of the time. The adapter...
thingiverse
This holder is designed for two 2.5 inch SSDs in place of a single HDD. There are no screw holes for SDDs, they will slide in and out freely. It is not really designed for 2.5inch HDDs because there is no way to dampen the vibration from them. ...Print...
thingiverse
HDD Enclosure. No special setup needed. ...If you print with mesh down (see images) you dont need adhesion or supports.
thingiverse
A modular 3.5-inch Form Factor HDD mount with M4 nut slots The width is such that 8 HDDs stacked make 265mm, which is the shorter side inner length of a Euro Box that I own.
prusaprinters
A simple adapter to fit a 2.5 inch SSD or laptop HDD to a PC case with mounts only for 3.5 inch hard drives.Sadly do not have a photo of this one, since it was specially made for a customer and then never seen again. So here are some OpenSCAD...
thingiverse
A protective enclosure for 3.5 Inch desktop size SATA hard drives (HDD).** The rear cutout allows easy access for USB-SATA adapters. Use the vertical drive rack to organize a collection. ... ** This is a resized version of the 2.5 inch HDD Case
thingiverse
I created this bracket because my case it's 2.5 inch slots only fit SSD's and not HDD's and my 3.5 inch slots don't have mounting holes for 2.5 inch. I have uploaded 4 different versions to choose from based on your mounting preferences. ... It...
thingiverse
I created this bracket because my case it's 2.5 inch slots only fit SSD's and not HDD's and my 3.5 inch slots don't have mounting holes for 2.5 inch. I have uploaded 5 different versions to choose from based on your mounting preferences. It...
thingiverse
Caddy for 2 SSDs in one HDD tray with honeycomb pattern for better cooling ## Added V2 with more features * Connector cut out * Small stops for SSDs Added FAST version (Use only if temps are not a problem) * Use for faster printing and less material...
prusaprinters
Caddy for 2 SSDs in one HDD tray with honeycomb pattern for better coolingAdded V2 with more featuresConnector cut outSmall stops for SSDsAdded FAST version (Use only if temps are not a problem)Use for faster printing and less material usageNo...
thingiverse
While searching for a harddisk bracket to install a 2.5 inch SSD into a computer having only a 3.5 inch slot, I found some brackets not meeting my requirements. Either support was needed or the holes for the harddisk screws were not countersunk...
thingiverse
... but the only place left was a CDROM player which I never use anymore. ...Removing that would leave a large opening in the front so I designed a bracket to install a 3.5 inch harddisk in a 5.25 inch slot which nicely closes the front of the computyer.