3 5 to 5 25 drive adapter bracket 3d models
2666637 3d models found related to 3 5 to 5 25 drive adapter bracket.thingiverse
Thing allows you to mount 3.5-inch device (like FDD - Floppy Disc Drive or Card Reader) in to standard 5.25-inch PC Drive Bay (meant for mounting DVD alike devices) Print Settings Printer: Prusa i3 Rafts: No Supports: No Infill: 100% Notes: I have...
thingiverse
... ...http://www.thingiverse.com/apps/customizer/run?thing_id=1279411 Instructions Using the following options: th = 2.5 tb = 5 rod = 3 f = 30 d3 = 1.5 d5 = 1.5 d5s = 3.5 sd = 5 sf = 0.006 h5 = 41.53 h3 = 25.4 d5sl = 8 ho2h5 = 21.84 ho1h5 = 10 hoh3 = 5
thingiverse
The holes that line up with the hard drive are 4.0 inches apart, the holes that are used to mount to the drive bay are 3.1 inches apart. The hole diameters should be close enough to use the fasteners you may already have. ...Print Settings Printer...
thingiverse
... adapter. ...This one uses less filament. I believe it is still structurally sound, as the tension is on the mounting points and the drive and case, instead of the center beam. Should print faster too. Thanks usermod for the original idea! ... V.
thingiverse
I needed to create put 3.5 drive into 5.25 slot. ...Made this small adapter.
thingiverse
... but I needed a place to put a bunch of hard drives, so here we go! The original thing didn't fit my 5.25" bay holes, and since I think they are pretty standard I remixed this into something usable. ... Now I can fit 2 3.5" drives in each bay!
prusaprinters
I designed this model to fit in a HP Z240 full tower chassis. ...This will probably only work in computers with tool-less drive installation that is similar to the HP design.
thingiverse
Bracket to mount a 2.5" Drive into a 3.5" drive bay. With buckle for easy fixing into the bay. ... Installation of the gate requires care.
thingiverse
I made this to fit a slim optical disc drive and a 3.5" flash card drive to a single 5.25" slot in a computer case that has very little room. It seemed impossible to find such an adapter as commercial product even on the Internet. There was one but...
thingiverse
Three part print for adapting a 3.5" drive into a 5.25" drive bay. Make sure to align the front surface of the front plate down. Use four M3x6mm screws to attach the front plate to the side braces. ... Designed to mount the 3.5" drive from underneath...
thingiverse
3.5" to 5.25" drive bay adapter for mounting your 3.5" HDD in CD-ROM compartments. Adapter designed according to SNIA specifications and could accommodate two standard 0.7"-high drives or one 1.028" and additional 0.7" drives in standard 43mm-high...
thingiverse
This is a basic but functional 5.25 to 3.5 inch hard disk adapter. Why make yet another one? - This one should be extra easy to print with the tear-drop holes - It can accept standard 6-32 hard drive screws that self tap into the holes. -...
thingiverse
Spade - Infil to add weight, no supports Letters - Print flat, already scaled to fit nicely in the embossing Star - Infil to add weight. Full print with 4x4x4 walls/top/bottom and 38% infil came to about 48g in weight. Glue in lettering and...
prusaprinters
A very basic part for my computer.I made two versions, one with a bottom part that keeps it all together, and one with the two sides as separate pieces for faster printing with less material (and fits on smaller bed sizes)Originally published on...
thingiverse
An adapter that converts 3.5 "hard disks to 5.25" bays. If your computer case has insufficient hard disk space, this part to make use of the remaining 5.25 "bay. Designed to be simple, fast build and durable without decoration. ...It is recommended to...
thingiverse
Simple bracket for mounting 2.5" drives to 3.5" enclosures. ... Note: the side holes are 3.25mm diameter and *not* threaded but can take standard screws as long as you don't overtorque them.
thingiverse
It has the side mounting holes for the 2.5" drive and it has both the bottom and side threaded holes to fit in the 3.5" caddy, to the same specs as a Seagate hard drive. ...Uses about 10g of plastic.Works with a set of 4 or more M3 x5 standard PC...
pinshape
This is a 5.25" to 1x 3.5" and 1x 2.5" drive bay adapter. It is pictured with my previously designed 3.5" to 2x 2.5" bay adapter mounted in the 3.5" slot. Printed in PLA, with 20% infill, weighs only 83 grams. This model can accommodate both 7mm and...
thingiverse
This is a 5.25" to 1x 3.5" and 1x 2.5" drive bay adapter. It is pictured with my previously designed 3.5" to 2x 2.5" bay adapter mounted in the 3.5" slot. Printed in PLA, with 20% infill, weighs only 83 grams. This model can accommodate both 7mm and...
thingiverse
An adapter so you can install 3.5" drives in 5.25" drive bays. You need two of them! Edit: New version uploaded. ...Old version was silly lol.
thingiverse
A front panel adapter to install 3.5" panels in a 5.25" slot on desktop computers.
thingiverse
Drive bays from **5.25" to 3.5"**. Perfect fitting for Cooler Master Silencio 550, but it should be for other cases. This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/6no3Y02Rhw9
cults3d
Internal 3.5" hard disk adapter for 5.25" bay mounting (CD Rom) Suitable for 3.5" IDE and SATA disk
thingiverse
Adapter from 3.5" to 5.25". Rough version made for further machining and painting. I will also leave the original file so that You can adjust this model to your needs. I will be glad to remixes. ... Scroll down ↓ ↓ ↓
thingiverse
This design is a recreation of a 3.5" to 5.25" adapter that I got with one of my computer cases. It provides great spacing for air cooling if you mount more than one HDD verticallly and is as-open-air-flow-as-I-could-get-it (altough I admit that it...
prusaprinters
This adapter allows to put a 2.5 drive in a 3.5 bay keeping the connector in the same place.Dimensions and screw holes are exact taken from drives specifications.Useful if you have a server caddy.Model is upside down for printability without...
thingiverse
This adapter allows to put a 2.5 drive in a 3.5 bay keeping the connector in the same place. Dimensions and screw holes are exact taken from drives specifications. Useful if you have a server caddy. ... Design available in onshape.com: ...
thingiverse
Adapter for 3.5" to 2.5" drives. Designed for the CM Storm Scout case's drive bays but may work for others. Final dimensions not fully verified, print at own risk. A 9/64" or slightly smaller drill bit is needed to remove the sacrificial bridge,...
thingiverse
Universal 3.5" drive adapters for mounting in a 5.25" drive bay. Upper row of holes are for floppy drives (for those of us who still enjoy that vintage grinding noise), while the lower row is for HDDs (SSD mounting plates can utilize both). To this...
thingiverse
The reason I made this was to make it possible to "stagger" hard drives in a computer case within the 5.25 bays. I thought maybe it would be better for heat distribution, but mostly I did it to see if it was possible to flip the model. I have no...