3 hose offset 3d models
721701 3d models found related to 3 hose offset.
prusaprinters
This type of connector just need 2 connectors to connect 2 drip hoses to one water hose. Additional parts you need2 standard gardena style hose connectorsrubber ring from a male hose connector Print instructionsMain Part:use PETG or ASA (I...
thingiverse
Plug for your American garden hose. ...No support needed for printing. 2mm wall thickness. (The black cap is not included.) (Proper 3/4-11.5 National Hose Thread!! ...AKA 3/4GHT)
thingiverse
This device is designed specifically for adapting a 6-inch portable air conditioner hose into a more affordable 4-inch clothes dryer hose.
prusaprinters
Some adapters for standard 38mm vacuum hose. ...All of them screw onto the hose itself, using the spral shape as thread.
thingiverse
A straightforward fix for running hoses along a chain link fence without relying on zip ties or metal hooks that can damage and scratch the surface.\r\nI need to run hoses for my automatic irrigation system while keeping them elevated off the ground...
thingiverse
(to wrap hose) - 47.11mm (1.85") Length - 126.7mm (5") 1" (25.5mm) gap down the center to squeeze in the hose Print settings I used (adjust as needed) 200 / 60 temps No Supports / Adhesion 15% infill to give buoyance Placed on 4 foot hose section...
thingiverse
Hose adapter holder for Gardena and other adapters. ...Available for 1", 3/4" and 1/2" threads.
thingiverse
This is a male connector designed specifically for a typical 3/4 inch water hose used throughout the United States.
thingiverse
Users love using the hose holder to coil up their hoses and keep them tidy in their garden or any other area. The tough, heavy-duty holding design makes it easy to store long lengths of hose. In a picture you can see 20-25 meters of hose neatly...
thingiverse
... off which I could only reach the outer surface. I attached the pull cord to the old hose and pulled it through the holes as I took the old hose out. Then I used thie puller to pull the new hose in. ...It is a tight press fit so no clamp was needed.
thingiverse
A short video demonstrates how a standard 3/8" hose, commonly employed in homebrewing with an outer diameter of 1/2", can be fastened to a wire rack shelf. ...The attachment enables the hose to dry in a vertical position.
cults3d
Made to stop a 3/4" (Outside Diameter) air line hose from being fully retracted into the hose reel, adjustable Bumper Stop Use with 2 Metric Bolts: M6 x 1.0 and a Length of: 30mm
thingiverse
Hose clamp organizer for 8mm duotight EVA Hoses: 1, 2, 3, ou 4 ways Waterproof double-sided tape can be used to adhere to the inside of your kegerator
thingiverse
Quick little bracket design for 38 mm swimming pool hoses. ...I needed this to fixate the hoses running up the roof for the pool heater. ... Printed with PETG on my ender 3 pro with MicroSwiss hotend.
thingiverse
Prints without supports, based on https://www.myminifactory.com/object/3d-print-wall-pass-through-and-filter-kit-for-3-4in-bsp-thread-117681 25mm is outside diameter of the hose (scale for different hoses).
thingiverse
While installing a bilge pump with 3/3 in vinyl hose the bend was a bit to sharp and the hose flattened. Rather then putting in an elbow which would reduce the flow I made this hose splint to keep the hose round. I made and installed the 4 screw...
prusaprinters
I needed to tidy up my garden hose setup and created these small and easy to print holders to screw into the house (3 or 3,5 mm screws works well). Designed for 13 mm (1/2" in freedom units) hoses - e.g. Easy to remove the hose if needed.I've...
thingiverse
A small wall mounted air hose end holder for a 1/4" recoil hose from Lowes. Uses #8 countersink screws. ...A single top screw was sufficient in my case.