3 sided fidget spinner 3d models
932989 3d models found related to 3 sided fidget spinner.
thingiverse
A snap together fidget spinner for standard 22mm OD x 8mm ID x 7mm tall skateboard bearings (608zz). The ballast bearings are exposed and can spin independently of the inner bearing. ... Everything is friction fit; I've played with mine for weeks and it...
thingiverse
I liked the idea of the usb fidget spinner but didnt need any more usb dirves so i took the neat design and removed the usb slots and replaced them with holes for bearings. i will mention that the two outer holes for the bearings is a real snug fit...
thingiverse
My son wanted a fidget spinner and I had some 8.5 mm steel balls around so made him this. I printed it in two halves so that you trap the balls within rather than making them so they pop in. Glue the two halves together. Takes a standard 608RS...
thingiverse
:) A tri fidget spinner I made in 123D Design. Uses one skateboard bearing together with three hex M8 nuts. !READ THIS! Right from the bat the sockets for the hex nuts are a little bit too small, so use a lighter to heat them up, then push the nuts...
thingiverse
... have that will work! Also the picture of my high point balancer is a crutial step in the spinner process! Good balance gives you a very stable spin and longer spin times! I used hot glue to balance this spinner, so far so good! ... ENJOY!!!!!
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=188275 Instructions Using the following options: Ring_Size_Selector = 20.37 Knurl_Width = 3 Font_Height = 0 Bands = 3 Message = FIDGET THIS! ...Knurl_Height = 2 Manual_Ring_Size = 18.35 Font =...
myminifactory
This design is a little thicker and heavier than a normal spinner, but it's still manageable. The center ring is 9mm tall (ball bearing is 7mm). The ring has 6 recessed areas so that the screws will go into and help hold the center ring in place. I...
thingiverse
Three standard 3/8 nuts will press-fit on the outermost points I have only printed the parts in white ABS but have included renderings in red as they look amazing! Hope you guys enjoy! Be sure to post a "Make" if you made them yourself and...
thingiverse
Careful this spinner uses 6700ZZ bearings... ...I had them around.... Spinner uses m3 screw and nut. Video of the spinner: https://www.youtube.com/watch?v=Y3K-K6oaDZE You can find the motor on my profile. ... Print is done in colorfabb xt.
thingiverse
This design is a little thicker and heavier than a normal spinner, but it's still manageable. The center ring is 9mm tall (ball bearing is 7mm). The ring has 6 recessed areas so that the screws will go into and help hold the center ring in place. The...
thingiverse
I came along a fidget toy on YouTube. It looked 3D-printed so I could make it. Use some (old) skate bearings in the holes and push the knobs in the middle bearing. ...Print Settings Printer Brand: Robo 3D ...
thingiverse
This spinner uses a 608 bearing in the middle, and 1/2" steel ball as weights. Steal-Balls I've used can be found here I recommend VXB for bearings. You can use your preferred cap for the bearings, there are so many versions out there. ...Print...
pinshape
This spinner uses a 608 bearing in the middle, and 1/2" steel ball as weights. Steal-Balls I've used can be found here I recommend VXB for bearings. ...You can use your preferred cap for the bearings, there are so many versions out there.
thingiverse
Customized version of http://www.thingiverse.com/thing:2144017 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=2144017 Instructions Using the following options: sections = 3 radius = 3 whichWeight = 3/8
thingiverse
... of http://www.thingiverse.com/thing:2101254 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=2101254 Instructions Using the following options: rotation = 150 whichWeight = 3/8 overlap = 2.5 objects = 3 radius = 2
thingiverse
Customized version of http://www.thingiverse.com/thing:2144017 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=2144017 Instructions Using the following options: radius = 3 whichWeight = 1/2 sections = 3