3.5 hdd adapter 3d models

This is a triple SSD to 3.5" HDD Adapter. Attention! The height is more than one standart Slot! The SSD´s have enough Space to get them cooled with ahFan from behind and the Power and Data Cables fit. ... UPDATE: Double SSD Adapter in Downloads ;)...

after dismantle and sealed external drive i came across this USB adapter board wich can be used with any brand of drives, so i designed this to make it usefull !

5.25 Inches to 3.5 HDD Adapter fast print

This is an adapter to mount a 2.5" HDD in a 3.5" slot.

An adapter to put a 2.5" HDD in a Trayless Mobile Rack. The same as version 1 but identified "Linux", "Data" and "Windows. ...And always the 7mm to 9mm adapter.

An adapter to put a 2.5" HDD in a Trayless Mobile Rack. Print, put 2 screws, and enjoy our hard disk drive ;o) In case your HDD is 7mm thick, you will need the "entretoise" and a bit double-sided tape... ...Enjoy

An 2.5" SSD/HDD adapter with a hexagon pattern. One to four m3 screws are needed to secure the disk to the plate. ...I have also uploaded the .STEP file so you can change anything to suit your needs.

The SSD drive or 2.5 hdd is held in the tray by four tabs which you may need to file to fit your drive. The holes in the side rails are meant to be used by a quick change adapter and are 3mm in diameter. ...I made the adapter in Cubify Design 2014 and...

Hard drive adapter made to fit a 2.5" SSD into a 3.5" tray. ... Holes on the sides match standard 3.5" drive mounting holes.

un adaptador para colocar los discos duros de 2.5" (notebooks) a disco 3,5" del tamaño de los gabinetes de PC de escritorio

My dangling 2,5" SSD needed a more professional (final) way to be installed in my Acer H340 case. The solidworks file has 3 configurations - for screw mount - e.g. ...if you want to install it with screws in a desktop computer - half and half - 2 pins...

A HDD mounting adapter to install a 3.5" hard disk in a fujitsu primergy TX140 server You need two adapters. ...Attention: the second one must be mirrored - you can mirror this in your slicer software

Mounts a standard SSD into anything that takes a standard 3.5inch HDD. Mounting holes for SSD and mounting holes for HDD. ...Made to fit into the stock Dell hard drive tray.

Remix of http://www.thingiverse.com/thing:29628 This is OrangePi Plus 2 to 3.5 HDD adapter This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/dhScpW98yiN

3D printed 2,5" HDD (SSD) to the 3,5" HDD place in computer.

The overall height from the very top of the top drive to the bottom of the bottom drive is 1 inch, which is the thickness of a 3.5 in. HDD. I uploaded Sketchup file, so you can customize the thickness as you wish. The file here is set at 6mm thick,...

This remix is adapted to reduce the amount printed material. ... Original design: https://www.thingiverse.com/thing:1706655

This remix is adapted to reduce the amount printed material. ... Original design: https://www.thingiverse.com/thing:1706655

This adapter allows you to mount two 2.5" HDD or SSD drives in a 3.5" Slot. The adapter has mounting points on the top and sides with the same spacing as 3.5" drives have. Also there are holes with 30mm spacing as floppy disk drives use them. ...

Another 2.5" to 3.5" hard drive adapter. I sliced this adapter using the cura extra fast profile 0.3mm layer height and set the wall thickness to 1.2. ...It takes approximately 42 minutes to print 2 pieces.

I have wanted clean and low profile dual hdd and less material printing. ... This is remake from https://www.thingiverse.com/thing:191942

I removed its drive bay, because it was at the bottom, where giant GPU+cooling (see my TESLA M40 92mm fan adapter) would go. So I needed to find place where the RAID array would go. The design by Schoba was what I needed - simple and easy to...

2,5" to 3,5" SSD/HDD adapter

This is a remix of the 2,5" to 3,5" HDD/SSD adapter by Tadziurski. ...Added a third mount hole as my case did not provide the outer most one.

2 3.5" HDD mount adapter for Antec NX200 Case. ... After installing long PSU there was no room left for the HDD's, so I have made this to install the HDD's

I have designed little compliant inserts that allow you to repurpose the 120mm AIO bracket in the DAN A4-SFX to mount a 3.5" HDD if you have a short GPU. The compliant legs slot into the slots on the AIO bracket and provide a hole to screw a 3.5" HDD...

Features an offset so that a standard 3.5" HDD ends up sitting 17mm left and 10mm up relative to the original plate. This is to make more space for cables or fan hubs mounted to the right of the HDD on the inside “wall” of the front panel (note that...

Very simple and minimalistic 2.5 inch HDD or SSD to 3.5 inch adapter

Very simple and minimalistic 2.5 inch HDD or SSD to 3.5 inch adapter

Use this bracket to adapt the 2.5" drive for use in a 3.5" drive space. Instructions This is designed so that a UNC 6-32 screw can tap into the plastic of the 3.5" drive mounting holes. 2.5" drives use M3 screws - the holes for them on this bracket...