3.5 inch hd 3d models
1113472 3d models found related to 3.5 inch hd.thingiverse
These are stackable 3.5 inch hard drive trays. They have low sides and holes in the bottom to save on plastic and increase air flow around the drives. They have screw holes to mount the drives. However, a lip on the front also keeps the drive...
thingiverse
With this caddy you can load 2.5 inch SATA disks in a 3.5 inch hot-swap bay. Use 2.5 mm pins to anchor the disk in the caddy. ( see pictures ) The height of the 2.5 inch drive can be adjusted in the openSCAD file. The .stl file contains a version for...
thingiverse
BabyMOD specs : - SquishX layout - DJI Vista supported (Should work with Frost Byte as well of course) - AIO, 16x16 and 20x20 mount patterns - Top plate with 20x20 mount (always handy) - Supports facing down USB whoop boards - 2.5 inch : 9mm motor...
thingiverse
Non printable parts: Eachine minicube flytower, or other 20mm mounting hole FC and 4in1 ESC Runcam split2 30mm 11XX motors eachine VTX03 2inch propellers Battery 3S 300-550mAh Alloy pillars - adjust lenght (my 21mm) 8x Screws M3 (stell, but better...
thingiverse
... the box and let it dry. Slide the front of the HD between the front clamps, push the back side into the back clamps. Use any screws or little bolts to screw the lid on. ...The screw holes are 3mm and go all the way down to the bottom of the box.
thingiverse
This version of the HD Enclosure is ever so slightly smaller and uses a sliding lid so that you don't need to use screws. Instructions Build, put hard drive in enclosure, slide lid into place. ... Get...
thingiverse
I made 2 other designs based on this one that are way better : The [MOD-L (with separate arms, from 3 to 5 inch)](https://www.thingiverse.com/thing:4295478) and the [BabyMOD (Unibody 2.5/3/3.5 inch)](https://www.thingiverse.com/thing:4660219). The...
prusaprinters
A 3.5 inch resize of this model https://www.thingiverse.com/thing:417402. The model in the picture is printed in Prusa PCBlend Natural.Requires support from build plate and a raft, as per the OG model. ...Maybe a draft shield too if from a high temp...
thingiverse
This is a little bracket for mounting 2.5" drives in 3.5" places. ...
cults3d
This is the best frame to replace your PROTEK35 or Cinelog35 AIO FC / ESC - 40-45A 4-6S Motors - IFlight XING 2205 2300KV HD FPV System - Caddx Vista FPVProps - 3.5 inch (iFlight Nazgul 3535 / Gemfan D90-3) Camera - GoPro Hero 6/7/8/9/10 BEC Battery...
thingiverse
Stand for two 3.5 inch hard drives. For my home RAID system. ...Printed 4 at once.
cults3d
Stand for two 3.5 inch hard drives. For my home RAID system. ...Printed 4 at once.
thingiverse
frame to mount a 3.5 inch speaker inside a box. ...I custom made this for a particular speaker I had lying around.
grabcad
3.5 inch NACA duct with 30-degree hose leg, half inch mounting flange at the base and integrated debris screen. I 3D printed this with carbon fiber infused nylon with amazing results. ... You can fit this on a small printer bed as long as the model is...
thingiverse
I basically designed it as my other hobby is origami and boxes like this are great for carrying around standard 7.5 cm / 3 inch square origami paper, but of course they are getting harder and harder to fine as no one uses them any more. ...So I built...
cults3d
I basically designed it as my other hobby is origami and boxes like this are great for carrying around standard 7.5 cm / 3 inch square origami paper, but of course they are getting harder and harder to fine as no one uses them any more. ...So I built...
thingiverse
version 3.5 pouces de la meteck 5 pouces cette frame est compatible walksnail, vista et O3 et analogique compatible AIO et stack 20X20 même de grand format moteur conseillé: 2004 / 2005 / 2203 / 2204 /1806 KV entre 2400 et 2750 en 6S et de 2900 a...
pinshape
I basically designed it as my other hobby is origami and boxes like this are great for carrying around standard 7.5 cm / 3 inch square origami paper, but of course they are getting harder and harder to fine as no one uses them any more. So I built...
thingiverse
Drive cover from the "USB and Audio 3.5 Floopy Drive Cover" but with no holes.
thingiverse
A simple guage for measuring lobster. ...This one is 3.5" to comply with USVI sizing regulations.
thingiverse
A very basic no-frills 3.5inch HDD holder for 4 drives. ...Designed to be very easy to print, I may post a version with screw holes to secure drives in the future
thingiverse
Why buy em when you can make em. ...Extra wide ring works great in a bucket lid. Drill a 3.75 hole in bucket lid and slide it right in. ...You do have to use supports (at least my machine does) no matter which way you print it.
3docean
Model formats: - *.max (3ds Max 2008 scanline) - *.max (3ds Max 2008 vray) - *.fbx (Multi Format) - *.obj (Multi Format) - *.3ds (Multi Format) - *.mb (Maya 8.5) - *.lwo (Lightwave 6) - *.c4d (Cinema 4D 11) renders Are made in 3ds Max 2008 using...
thingiverse
This is a 2.5 inch to 3.5 inch SSD adapter. ...Very easy to print.