3.5 inch ssd 3d models
1086701 3d models found related to 3.5 inch ssd.thingiverse
This is a 2.5 inch to 3.5 inch SSD adapter. ...Very easy to print.
thingiverse
This design is an attempt of converting mounting holes of 2.5 inch disk drive to 3.5 inch form factor. The SATA interface port should remain in the same place which is useful for upgrading your old ALL in One PC with a SATA port connector fixed. ...
prusaprinters
A simple adapter to fit a 2.5 inch SSD or laptop HDD to a PC case with mounts only for 3.5 inch hard drives.Sadly do not have a photo of this one, since it was specially made for a customer and then never seen again. So here are some OpenSCAD...
thingiverse
This is a small ssd holder. I made a design on it, where it says in Russian letters "Mom, this is for study." There is a version without design. ... The distance between the holes to make sure it will fit you are shown in the photo.
cults3d
Bracket to mount a 2.5" Hard Drive or an SSD Hard Drive into a 3.5" hard drive bay
thingiverse
Bracket to mount a 2.5" Hard Drive or an SSD Hard Drive into a 3.5" hard drive bay Instructions Mount Hard Drive into adaptor first.
thingiverse
... Bracket to mount a 2.5" Hard Drive or an SSD Hard Drive into a 3.5" hard drive bay Installation Mount Hard Drive into adaptor first, two screws on an angle across the square opening should be sufficient if the holes don't quite line up properly.
thingiverse
... this model; two that fit 3x 7mm high SSD and two that will fit 2x 8mm+ SSDs. For each mount there's a full sized 3.5" tray and a "stubby" tray that's only 101mm long, for cases where you're going to mount using the front four mounting screws only.
thingiverse
I needed a SSD tray to put three ssd drives into the space of two 3.5" bays. These fit my drive sleds for my Corsair 650D case, but should fit in any 3.5inch drive solution. I provided the option to mount a 40mm fan to the tray if desired. I did...
thingiverse
It's a 2-piece adapter to turn a 3.5" drive bay into an externally accessible slot for a 2.5" SSD. Uses SATA extension p/n 29652A (EAN/UPC code 4043718180448) for the connector. 2 M3 screws attach the extension cable. 2 M3 nuts in slots allow for...
thingiverse
My new 2.5 inch SSD is nice but the slot is 3.5 inch. **sigh** I printed a nice tray, but it needed screws that I didn't have **sigh** I tossed this model together with the intent that it not need any screws. The SSD should fit snug in the...
thingiverse
I was looking back at my old designs, and saw an SSD mount I had made. I was inspired to go back and make one that works with metric screws (M3x5mm) and that uses much less material. ...I haven't actually printed it yet, so try it and let me know how it...
thingiverse
This holder is designed for two 2.5 inch SSDs in place of a single HDD. There are no screw holes for SDDs, they will slide in and out freely. It is not really designed for 2.5inch HDDs because there is no way to dampen the vibration from them. ...Print...
thingiverse
mSATA SSD to 3.5 inch Hard Drive Bay Adapter. Required parts: - mSATA to SATA adapter like here: https://www.aliexpress.com/item/2017-Universal-mSATA-SSD-To-2-5-Inch-SATA-6-0-Gps-Adapter-Converter-Card-High/32613616694.html - 2x screws M2x5.5 (or...
pinshape
Simple 2.5 inch to 3.5 inch SSD/HDD drive converter. Why have simple air holes when you can have a nifty design! ... Printed on Makergeeks Pearl White Raptor PLA .2 mm Resolution. Doesn't need rafts or supports
thingiverse
Model of standard size 2.5 inch SSD hard drive with accurate mounting screw position and sizes.
thingiverse
This is a triple 2.5 inch SSD holder for desk use. The sizes of the holders may not fit your personal needs. Just drop it onto your designing software and resize them. ...Hope that this helps you out
thingiverse
Just a quick and dirty sled (mount, adapter) for 2,5 inch SDD to mount in 3,5 inch PC case disk bay. You can sightly shrink side holes in order to tap them. I have a quick mount system in my PC case, so hadn't need threads. ... Designed in Fusion 360 -...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=384919 Instructions Using the following options: lidInsetOffset = 0.0 coverThickness = 1.0 lidInsetHeight = 4 tabSize = 1 interiorFillet = 2.0 hingeFillet = 3 interiorHeight = 11...
thingiverse
... для установки жестких дисков в системный блок. ...Позволяет установить HDD либо SDD диски на полки системного блока 3,5 дюйма (под стандартные HDD) либо 5,25 дюйма (под дисководы). ...Главное преимущество - минимальная себестоимость и скорость печати!
cults3d
This is a tray to fit 2.5 inch SSD drives into the 3.5 inch Dell's server slots.
cults3d
This is the same tray that comes with QNAP NAS devices. ...This part fits the 2.5 inch SSD and HDD drives into the 3.5 inch slot.
thingiverse
HDD/SSD wall mount with air flow holes. ... Print with supports, 100% infill. 2 versions - 3 and 4 holes for screws
prusaprinters
Quickly added some "speed holes" to improve airflow in the enclosure I'm putting this in as a blank to fill an empty SSD spot. Holes added by subtracting a couple cubes from the original model in Microsoft Builder. ...Eyed them in the center somewhat,...
thingiverse
This is an adapter for 2.5 inch hard drives or SSDs in a Cooler Master tower. My case came with one, but I recently replaced some mechanical hard drives with SSDs, and I needed more. ... This is basically a copy of the one provided, minus any holes in...
thingiverse
This is a rack that I designed because I wanted a large external storage and had a few 2.5 inch hdd's laying around. I did a little amazon shopping and bought a couple SATA to USB cables so I can connect them to the computer. ...Hope this model is of...
thingiverse
Quickly added some "speed holes" to improve airflow in the enclosure I'm putting this in as a blank to fill an empty SSD spot. Holes added by subtracting a couple cubes from the original model in Microsoft Builder. ...Eyed them in the center somewhat,...
thingiverse
I made this case to fit my 2.5" Hard Drive, but it should also work great for 2.5" SSDs as well. The case fits snugly and the top does not come off on its own. ...The hole for the SATA to USB cable should be big enough for most cables, but may need a...