3.5 ssd drive 3d models
1083548 3d models found related to 3.5 ssd drive.thingiverse
... let me know. Printed with 25% infill in ABS it was plenty strong for this purpose. The model was designed in Fusion360 using the SFF Specifications for 3.5" Magnetic Drives and the Crucial MX500 2.5" SSD Features document for the measurements.
thingiverse
2.5" Drive to 3.5" Drive Adapter. Should fit most applications. ... Super simplified, reversible, and thin for ease of printing.
thingiverse
simple 2.5" to 3.5" hdd adapter with 3 holes. holes align up perfectly. ... print in ABS to reduce chance of plastic warping once installed into a pc case.
thingiverse
Fits inside of HP workstation/desktop guide rails so you can keep using the easy rail system instead of tearing apart the case or just letting them hang by the sata cable.
thingiverse
a 3.5 drive caddy that holds 2 ssd drives in a single drive bay made this in a pinch when I added a second ssd and the power cables limited me to the 3.5 drive bays,,, after installing I do see it could use a set of locks like the hard disk has.
thingiverse
It's a common hard drive caddy to screw your 2.5" hard drive to 3.5" mounting desktops. If you print it, please leave us a comment with your thoughts. UPDATE: As stated in one comment below, to align properly HD cabling now V2 its mirrored in X...
thingiverse
Remix: Correct screw spacing. ... Allow for inset screw heads with print supports designed in the STL. Less material used in the bottom. Various options for side and/or bottom adapters for the 3.5 inch drive.
thingiverse
This is a small ssd holder. I made a design on it, where it says in Russian letters "Mom, this is for study." There is a version without design. ... The distance between the holes to make sure it will fit you are shown in the photo.
thingiverse
This is a drive caddy for mounting 2.5" SSDs or laptop HDDs in a 3.5" drive bay. Most new 2.5" drives come with their own adapter, but if you get a bare drive, or scavenge one from another computer/laptop/PS4 (don't ask), you're stuck scrounging for...
thingiverse
Simply click on **Open in Customizer** * Using the Customizer you may specify the dimensions of each slot or mix an M.2 slot with an SSD slot * supports 5mm to 11mm SSD drive height and 1.25mm or 2mm PCBs * use M3x12 to mount the optional sliding...
prusaprinters
Please let me know if you encounter any issues. These M2 / SSD adapters make it possible to mount two M2 SSDs or two 2.5" SSDs in one 3.5" hard drive mounting bay. Please measure the height of your SSD before printing the dual SSD adapter as some...
thingiverse
I designed this bracket to be able to install a 3.5" HDD drive in addition to one 2.5" SSD into my NZXT H1 v1 PC case. Just remove the original 2x SSD bracket and use my bracket instead. You will need some 90° angeled SATA connectors to connect the...
thingiverse
This adapter will allow you to use a 2.5" 7mm height SSD or hard drive (laptop form factor) in a Icy Dock hot swap bay. This was designed with the ICY Dock in mind, but should work for other similar designed hard disk enclosures. No supports...
thingiverse
A drive tray for a Z600 workstation that can hold either a 3.5 dive or an ssd with the included adapter. ...The tray needs support at build plate only to prevent sagging during print the adapter is fine with no support.
cults3d
Bracket to mount a 2.5" Hard Drive or an SSD Hard Drive into a 3.5" hard drive bay
thingiverse
Bracket to mount a 2.5" Hard Drive or an SSD Hard Drive into a 3.5" hard drive bay Instructions Mount Hard Drive into adaptor first.
thingiverse
... Bracket to mount a 2.5" Hard Drive or an SSD Hard Drive into a 3.5" hard drive bay Installation Mount Hard Drive into adaptor first, two screws on an angle across the square opening should be sufficient if the holes don't quite line up properly.
thingiverse
2.5” Solid State or Hard Disk Drives into one 3.5” drive bay. V1 - Minimalist/High Air Flow design. ... V2 - Sturdy/High Air Flow design.
thingiverse
This is a drive adapter from 3.5 to 2.5. ...allowing you to mount a 2.5 inch drive in a 3.5 inch drive bay. ...this was designed to work with the tool less bays but will work with either
thingiverse
Took original 2x 2.5" drive design and made it for just one 2.5" drive. Also cut out about half of material used by modifying length and cut outs in bottom. Also redesigned clips so that supports are not needed. ... Only works with 70mm thick drives.
prusaprinters
Remix to accept a 9mm drive. Category: Computer
thingiverse
... infill and it came out great. The two holes between the side holes and the SSD are for storing the extra two screws you will have left over from the hard drive. ... They could be special anti-vibration screws, as they are in the WL710AV All-in-one.
thingiverse
3.5" to 2.5" adapter for PC drives. ...May not work for certain configurations. Designed to adapt drive sleds from 3.5 to 2.5 for facilitating an SSD upgrade on an older machine.
thingiverse
mSATA SSD to 3.5 inch Hard Drive Bay Adapter. Required parts: - mSATA to SATA adapter like here: https://www.aliexpress.com/item/2017-Universal-mSATA-SSD-To-2-5-Inch-SATA-6-0-Gps-Adapter-Converter-Card-High/32613616694.html - 2x screws M2x5.5 (or...
thingiverse
2.5" HDD/SSD -> 3.5" 3.5" HDD -> 5.25" 3.5" HDD + 2.5" SSD -> 5.25" (Use 2.5->3.5 for SSD, has offset holes to align connector better) I know there's others out there, but I wanted a set that is a little more simplified. ... ...
thingiverse
I designed this to mount 2.5" drives in a 3.5" drive tray. I wanted an adapter that didn't use screws and was small enough to print on my MP Mini Delta. This adapter prints in two parts. The back part is semi-optional depending on how stable you...
thingiverse
Holds 3 x 2.5" SSD drives in place of a 5.25" optical drive. Recommend using a couple of M3 screws to secure it to the chassis. There are no screw holes to hold in the drives, instead, the width of the slots for the drives is slightly reduced...
myminifactory
This rail allows for 4 SSD's or other 2.5in drives to be mounted together. ... There are also mounting holes in the feet to enable it be attached to a case.