3d model examples

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

I restarted from scratch and designed this model from those other inspirations. This version allows a 5015 fan to be installed without interference to the left or right gantry positions. I placed the fan above the slightly relocated CR Touch...

A wrench is used to unscrew the end caps for relamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap. 7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protectionSuperior...

This would not work on a single nozzle printer, so we opted for truncated tetrahedra with slight insets on two of their triangular faces. INSTRUCTIONS Everything prints at 0.2 mm layer height.Set your line width to 0.45 mm, as the pattern...

Be very careful when inserting the blade.* Huge respect to Alexey Pavlenko for the idea of adapting the popular knife from Giacomini for printing ===================================== PS 21.03.05 I updated the files of this model. If you downloaded...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_top_port_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_shape = 4 custom_bottom_port_corner_radius = 5 custom_back_camera_y_size = 20 printer_tolerance = 0.4 custom_case_wall_thickness = 1.6...

You could also use hex stock cut to the same size, which would increase the weight (since the center of the nuts is hollow) and improve the spin time, but also increases the amount of work that needs to be done in order to build these.The nuts must...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_pattern_element_radius = 6 custom_top_port_corner_radius = 5 custom_back_extra_port_y_position = 30 pattern_line_thickness = 20...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_shape = 4 custom_bottom_port_corner_radius = 5 custom_back_camera_y_size = 20 printer_tolerance = 0.4 stencil_pattern_line_thickness = 30...

Cursed Immortality Season 2 - (2/4) The Umbratouched - Curse of Vengeance   Description Save money on this complete December Bundle, The Umbratouched, Curse of Vengeance, which contains all the models from the December release! These models come...

A great way to combat this on any print with sharp corners is to add “Mouse Ears”.• Add these in PrusaSlicer by right clicking on the model in the list on the right of the screen, hover over “Add Part” and select “Add Cylinder”• With the cylinder...

- Holes to close the Pitan now have modelled M3 threads - Redesigned for use with the hobbed nut that the stock Ender 3 extruder has, but I'm sure you can make it work with a hobbed nut like the original Pitan uses - Spring slot reshaped to work with...

Rafts: Doesn't Matter License The "Sidewinder X1 E3D Hemera FFC Riser" models (.stl) are licensed under the CC BY license by Code and Make. The "Sidewinder X1 E3D Hemera FFC Riser" code (.scad) is licensed under The MIT License by Code and Make. We...

...More importantly, Thingiverse hasn't run their customizer queue since Jul 10, 2020 so until they fix that issue, you will have to install and run OpenSCAD (free software) on your own computer to process the code to create your own customized models.

It will not fit a full sized stepper, use their model if you have the original stepper motor. I suggest printing with the end that hooks over the carriage on the bed with supports on bed only. There are minimal supports this way and the hook keeps...

3 perimeters 7 bottom layers on the cap ( definitely overkill ) 4 top layers Gyroid fill pattern ( any pattern will do ) Extra perimeters if needed was checked Seam position Rear ( make sure the hinge potion of the model is pointing towards the back...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_back_camera_x_position = 0 custom_top_port_corner_resolution = 8...

Found a simple hip flask just laying about USHip flask discovered seemingly abandoned USHip flask uncovered, left behind USHip flask in basic design chanced upon USHip flask, a basic model, was stumbled upon USHip flask, plainly designed, was located...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_extra_port_corner_resolution = 8 custom_bottom_fillet_radius = 1.6 custom_left_port_corner_resolution = 8...

The current model is sized for a 28mm long motor, if you get a longer or shorter one a new set of files will have to be generated. If you do not have access to Inventor let me know and I can generate the files for your size...

The spring just needs to be a close fit around the knife (1/2" ID). My model of the Roland-style knife is measured from one I bought online. I guessed at what was inside the screw in part and I didn't include the bearing. Yours may be different...

Update to v9: Put the K25 spring into the model, looks like it fits fine with about 2 whole whopping inches of precompression. Rounded off the corners on the PR guide (which isn't much of a spring spacer anymore) to help the spring go smoothly. Now...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

This also means that if you wanted to try to build a GoN NERD/NERD TKL, H87a, or the Kprepublic XD87 should all be able to fit - possibly with some small custimization to the model. More to come as I sort this out, but the files themselves are ready...

... satellite. The team’s website is http://csdc.uvic.ca/ Note that I did not create the Diamagnetic Payload Assembly, this was created by A.G.O. Environmental Electronics Ltd. The magnetorquers are not in the model, as they are still in development.

(This is all also in the README)I commissioned prints for these models using PLA with 40% infill and they work like a charm.- You will need to print the Rear Panel if you want to use the parts in the MOBO and GPU folders.- The PSU folder needs to be...