3d model of link

I'm a big fan of the textured rollers I keep wandering across, so I figured I'd add to the mix a few textures I wished were available. Found fairly patterned images online, inverted image, used online lithography tool to convert into textured...

This tutorial will guide you through the process of establishing this connection. Step 1: Set Up Post Builder NX CAM To begin, open your Post Builder NX CAM and create a new project. This will involve setting up the necessary parameters such as...

... PLA. Colour to suit  Notes: Not a lot to do in cleaning this one up as the edges are rounded/ filletted, so it's just a matter of wiping off any stray ‘hairs’ and it's ready to go.    Category: Office

Use the same settings in printing the rest of the Main Body and Tube Holder. Fill with shaved ice up to the second line before placing the Tube holder on top. You can also use plain water if you don't have an ice maker. Fill the Main Body with...

A personalized version of http://www.thingiverse.com/thing:56912 was created using Customizer! (http://www.thingiverse.com/apps/customizer/run?thing_id=56912). ...To customize, use the following options: Custom =...

As "normal" printed straps (fishbones type) would only allow to print 9pc at a time, I searched for a way to increase my batches to 50 pieces. The Thingiverse thing from veno0msho inspired me and I did: implement batch generator based on printbed...

It no longer makes sense to keep it.The print quality improved greatly compared to the original screen, not to mention that the curing time gets reduced because this is a mono screen (just like the 2k upgrade kit).You may need to contact ChituSystems...

You need to change the bottom and top plates, adding two spacers in place of arms and everything else. Nearly any 2-axis gimbal will work with this copter, but I designed one specifically for my low-cost yet surprisingly good gimbal solution:...

... the fan is on or you can modify Marlin slightly. Under MarlinMain replace the block of code similar to this around line number 1163: #if FAN_PIN > -1 case 106: //M106 Fan On if (code_seen('S')) { fanSpeed = constrain(code_value(),0,255); if(fanSpeed

Customized version of http://www.thingiverse.com/thing:739573 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=739573 Instructions Using the following options: minimal_color_layer_thickness is set to 0.6...

I found awl13A's holder and it does an extremely good job of holding the iron so I modified its base to fit my station. The holder swivels and has a hole for a 3mm locking bolt. I also thought it'd be smart to leave it removable as accidents will...

NATO/Picatinny Rail for Kowa TSN-883 Spotting Scope Use this to mount a red dot sight (reflex sight, finder) to your spotting scope. Includes FreeCAD source file in case you'd like to modify the part. Requires 2 pcs M4 x 20 screws with hex nuts to...

VERY IMPORTANT: After installing this bracket, you must raise the Z limit screw in the back of the printer! Don't do like me and get pulled away from the task by someone in the other room, then come back and blissfully attempt to print. Even nylon...

I like the idea from EddiePrints, but wanted a version where the Remote was not zip tied on, so i easy could remove it and use it somewhere else.Also wanted it on the other side of the printer. By this, you have to remove the remote on start op when...

You might need a sheet of paper around the ring to enforce this. Instructions: Print the 2 pieces. Zip tie the pen to the pen arm first. It will be awkward after the 2 parts are fitted together. The ring has one side with a gap for the...

Google übersetzt:Türstopper mit Magneten für die “Nullstellung”(Bild 3 und 4).Dieser Türstopper kann mit 2 Senkschrauben (Schaft der Schrauben 3 bis 4mm) an einer Tür befestigt werden.In der oberen Stellung verhindern 2 Magnete D6mm H3mm die vor der...

I've added a tab which not only adds a screw hole to mount it cleanly but adds a way to cable tie to the wires out of the way. I also moved holes to where I need them.</p> <p>I've have added new piece to put the wemos d1 mini I used for the...

This is a remix of the the Dark Eyes sonic by fetasigma that is compatible with the light and sound tube from the Personalize Your Sonic Screwdriver and Transtemporal Sonic Screwdriver toys. I haven't sanded and painted mine yet but wanted to get...

(Here a gargoyle frog) The platform can be fixed with screws and the angle can be adjusted with another screw. There are several versions available: Longer distance to the (fixing) edge. Different lengths for the adjusting screws Hole of the upper...

Assembling this piece requires only a couple of M3 screws to hold the latch onto the phone holder body. **QUICK NOTE:** The clip for this piece was designed with flexibility in mind when using ABS plastic, which may be more prone to bending than...

... resuming print. 8. Share! Please share and post makes! V3 - Corrected lines to be accurate to the official Texas Tech logo. V2 - Fixed some minor geometry issues that generated awkward layer lines in the middle of the print. ...V1 - Original Post.

... You can also use a tiny piece of cardboard as the base if you want. Once your mini hoop is set up, find a safe spot on your desk where you can play without knocking anything over. It's time to get ready for some fun and exciting basketball action!

Use M3 x 20 screws on the steering axles to ensure sufficient strength, taking note of a slight recess in the steering axle to accommodate the screw head. Use M3 X 8 screws to hold the aft bottom plate in place and M3 x 6 screws for the forward...

All of these were printed with PLA at 0.3mm layer height with no supports. These also print fairly quickly. I think you could print the whole bunch in about an hour, depending on how much you want. ... Programming Visual Aids (Variables) by...

Customized version of http://www.thingiverse.com/thing:193647 Created with Customizer! http://www.thingiverse.com/apps/customizer/run?thing_id=193647 Instructions Using the following options: Head type set to countersunk for precise fit. Socket...

A brand new release of the wildly popular Soda Bottle Bird Feeder with a gigantic perch for massive birds is here! They will be flocking to this one in droves! If you are keen on frugal filament consumption and want to do your part to prevent global...

When done correctly, this type of friction from printed parts could be used for the extruder drive mechanism too, replacing the metal pinch-wheels that we currently use. In any case it can already withstand more than the force the force that the...

I have attached two photos of what you'll need to edit in firmware. First photo is changing endstop to trigger when visual field is broken. Second picture is where you adjust manual home position. You adjust z value to change first layer height. Two...

Verify stability of phone clip and phone holder before driving. I am not liable for damages or fines incurred from using this file.</p> <h3> Print Settings</h3> <p><strong>Printer Brand:</strong></p> <p>Prusa</p> <p><p class="detail-setting...

For spinner connections, you'll need to connect directly to MISTer's USER_IO port or use a 32u4 micro as I did in my build, details of which can be found at...