3d print filament storage

I have recently upgraded my filament storage from a wall mounted bar to a cupboard for keeping them outof sight, this has lead to me needing a better solution to run the filament to my Printer. I have designed a dual M10 PTFE tube holder to allow...

In the bottom I put Silica Pearls (500g fit quite neatly beneath the support), then I put in this support and then I can put 3 spools on top and close the lid. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution:...

Empty Spool used for 3D Print Filament Plastic Refill

I have used an existing china cabinet with glass doors to store my filament, as it's already quite dry in my apartment. The storage unit won't be airtight, but will have enough desiccant inside to compensate. In addition to this project, you can...

here are some spool storages from some brands (TINMORRY, sunlu, fillamentum)

I use the AnyCubic Chiron 3D Printer and I used PLA filament. In order for me to get my desired product, I first place the grid in inches, then when I finished designing, I changed back to MM and centered the thing. ... Comments are welcomed, as well...

It won't substitute for an electric dryer box to fix wet filament but it should keep filament dry between uses. It is designed to be printed with no supports, no bed adhesion (no rafts, no brims) and common PLA. For the long tube, I have sometimes...

You could just put a thin piece of wood, plastic, or what ever underneath or make a little adapter for it.  So I made a little adapter to put on the end hook of the shelf arm and raise the front 3mm, this gives the shelf a slight angle so the spools...

Therefore i cut off the t-shaped think which would normally be slid into the doorframe (your model may vary). Mount the brackets by drilling the nescessary holes (wooden drill bits worked well for me) and sealing the perimeters of the brackets with...

Things to Buy: Clear Filament: 1.75mm: https://www.makergeeks.com/products/maker-series-petg-3d-filament-175mm-hd-clear-glass-1kg 2.85mm: https://www.makergeeks.com/products/maker-series-petg-3d-filament-285mm-hd-clear-glass-1kg Desiccant:...

 It's been in use for about a year now with no problems.Printing InstructionsSupport on build plate only for the small pegs and handle overhangI printed in Fiberlogy Easy PET-GNotesI have both the 60-Quart and 44-Quart versions of this box – the...

Print 2x `bowden_holder_*`, drill and mount it on front, attaching PTFE tubing though them. `bowden_tube_organiser.stl` can be glued on sides of box to hold unused PTFE tubes. Close your PTFE tubes using `bowden_tube_cap.stl`. As a bonus, when...

Example swatch printed with a precise layer height of 0.12 and full infill at 100%: 2020-08-12: Swatch box and lid upgrade completed A modified filament box is based on Witchhunt6991's original design found on Thingiverse, with some notable changes....

... to the wall and feed it into a printer. For optimal results, pause your slicer at 9.5-10mm Z-height to position the bearing [by printing at the front of the bed and rotating the piece 180 degrees in the Z axis, this process becomes incredibly easy].

Crafting an Unconventional Filament Organizer from Upcycled IKEA Parts. ...Project Still Underway.

Printed in PLA at slow speed / fine resolution with a Kentstrapper Galileo Smart. Some necessary sanding to the lower part of the lid was performed in order to achieve a perfect fit into the body part. The print took 20 hours for the body, which had...

I found myself requiring additional support and a raft to print the top layer successfully, although this was achieved using HIPS material and I still have some fine-tuning to do with it. ...Nonetheless, I appreciated the outcome and it has become a...

Using ABS-R, I printed out hangers from Thingiverse (http://www.thingiverse.com/thing:743280) and was pleased with the result - they seem strong enough to hold my filament in place. However, my screws were slightly too long, so I had to use a Dremel...

A simple filament swatch for PLA or ABS with a box to store them all in.

... Filament Dry Box Set (Updated 3/11/2021) This set of prints are designed for use with the following items to create a very slim box that will hold ever 1kg spool I have used so far. It will rub slightly with the YOUSU spool but it still works fine.

This is a remix from the Fitzterra Spool Drawer which fits for Sunlu Filament rolls. ... Use a M5 threaded rod for the holes.

... myself to toss them out. ...That is until I stumbled upon an idea on ALL3D - a storage solution using repurposed spool parts. ...The only problem was that accessing the free files required a lot of effort, so I decided to create my own alternative.

#Parts to print:# Print four front and back brackets and one humidity sensor bracket (optional). #Buyparts list:# * OBI Allzweckbox Cadiz XL mit 4 Rollen Transparent (container) * OBI Deckel für Allzweckbox Cadiz M - L - XL - XXL...

To bring a new use for the empty Spool. ...I designed it for a Spool from "Das Filament", so I don't know if it works for other companies. Just need a drill to make a 5mm diameter hole using the mockup for more precision. Enjoy! ...

To bring a new use for the empty Spool. ...I designed it for a Spool from "Das Filament", so I don't know if it works for other companies. Just need a drill to make a 5mm diameter hole using the mockup for more precision. ... Enjoy!

I store my filament in a 10 l Bucket (Obi if you are from Germany). In the bottom I put Silica Pearls (500g fit quite neatly beneath the support), then I put in this support and then I can put 3 spools on top and close the lid. ...

Print BOX with PLA or PETGPrint cover with transparent color (I printed it in vase mode.)Print each sample in 15 minutes z=0,3W

I opted for IKEA TROFAST to store my filaments. These containers are reasonably priced and most importantly, they fit perfectly into my cabinet. However, the lid has a large opening, which is originally designed for easy access. In order to prevent...

Spade - Infil to add weight, no supports Letters - Print flat, already scaled to fit nicely in the embossing Star - Infil to add weight. Full print with 4x4x4 walls/top/bottom and 38% infil came to about 48g in weight. Glue in lettering and...

Print instructions:0.2 LH @ 25% infill no supports.You will find 3 designs, some are thinner than the others and the top has different internal diameters to be compatible with some vacuum pumps.I used thin double-sided tape on the back of these rings...