3d print remote holder

I wanted to keep my projector and Sky Q Mini Box remotes organised in my spare room, so I made this holder. Each compartment is 50mm wide, by 30mm deep. ...The front and side walls are 60mm tall, the back wall is 70mm tall. Screw holes are counter sunk...

The Yaris Hybrid with Smart lock lacks a key barrel, so I removed the blanking plug and created this holder. My prototype is made from white PLA+ for testing purposes; I'll print it in ABS once my enclosure is complete. ... This design suits the...

A basic shelf for storing remotes (specifically designed for Philips TVs). ...The fit leaves something to be desired, causing it to slightly rub against the print on the control buttons.

This is a simple piece that connects two remotes so they always stay together. There's really nothing else to it. ...I printed at 0.32mm layer height with 20% infill.

I designed a stand for all the remote controls I have in my living room. ...I can place them flexibly and in different positions.I printed a hard version and a soft TPU version.

Produced in Tinkercad from scratch for an Epson Projector Remote.Ideally print with at least 4 walls to give the box strength. ... This is designed to be wall mounted.

Support for remote control installation: place the device in a 5cm wide slot. ...Post-Printing Instructions: Mount using screws or double-sided tape, attaching to a wall or stand.

Fits the two distant window and curtain remotes perfectly for the Velux system. ...The "glow in the dark" print makes them easy to locate, even in low-light conditions.

... The orginal one I had on my wall was bigger and was just a bad print, but I could never find the original file to reprint it, on all the major sites. ...Hope this helps you keep your tv remotes from getting lost in the recesses of your couch.

... to store the remote. Print instructionsMay be very tight fit. Works great, but if you jam the remote in there tight it is hard to remove, good but also possibly bad. Sanding the inside or bumping up the print size by a percent or two is advised.

... you jam the remote into the compartment too tightly, it can be quite tricky to remove - a double-edged sword, really. To avoid any issues, I'm advising myself to lightly sand the interior or slightly increase the print size by 1-2% before assembly.

Was made for the Smartmi Fan 3, but will fit any fan with a 38mm stem and a similar remote.I added some padding with automotive tape to protect the aluminium and secure the remote a bit tighter, as I don't use it at all.I printed in PLA with 3...

Didn't want to drill holes in my wall to mount the remote holder for my Panasonic air-conditioner. So I designed this to attach to the pillar of my rack where I put my printers. ...They attach using 2 cable ties.

This is a holder for a Duux Fan Remote. ...It has holes for two 8x5mm round magnets.Base and lid are separate and are glued together post process.Printer in PLA at 0.2mm layer height with 15% Infill.No support needed.

This is a holder for garage door remote. It has a hole in the back for attaching a keycord. That way it can automatically retract. It has a hole for the A button to open the door. Attach to a surface with 3m vhb tape. ...Now you can open your...

I quickly whipped this up because I desperately needed a spot to hang my heated blanket's remote control. After building it, I discovered that it serves as an excellent holder for my evening glasses as well. ...Command strips truly are lifesavers.

Remote control holder designed to securely attach to a 0.625-inch diameter shaft of a floor lamp purchased at Walmart, featuring a robust fastening system utilizing #8-32 heat inserts and two high-torque #8-32 bolts for maximum stability.

Do yo have a drawer and want a holder for your remote? ...This is for you. The one in the photograph has been done with prusaslicer default configuration, 0.15mm later height Scaling is possible in order to meet your necessities.

Just my modded design to hold the Meetup Remote without it slipping out of this holder. Will not wallmount this, will just stick it to the base Meetup bar with double sided tape. (removed mounting screwholes) Lenscap and tripod mount mods...

This is a simple TV remote holder that attaches to a wall or flat surface. The model is designed to use Gorilla mounting tape but it also has 2 4mm holes with a 1mm chamfer. ... To note there is no issue with the Gorilla tape sticking to any...

I crafted a custom remote holder specifically designed for my daughter's Roku device. ...The design has been uploaded to three different variations - one featuring the official Roku logo, a sleek and modern blank version, and an eye-catching "Unicorn...

A simple two-part holder for a remote control with a width of 22 millimeters is all that's needed. I used the TESA PowerStrip to secure it firmly on the backside of the TV, where it will stay put. The adjustable length allows it to fit any setup...

This sleek Samsung NU8000 Series TV remote holder boasts a minimalist approach that screams simplicity. ...While its straightforward design may not exactly set hearts racing at first glance, rest assured that a revamped version with a dash of flair is...

I designed a holder for a Technisat tv remote (TechniStar S1). The target was to have little material and a minimal design. There are two versions - one to fix with clue (in my case Tesa Powerstrips) and the other has two srew holes (e.g. ...3x12 TX10...

It's seriously amazing - the picture is incredible on my big Asus 28" 4K screen, and I needed a spot to stash the remote control. ...So, I quickly designed a holder using TinkerCAD and stuck it onto the lower left corner of the monitor with some hot...

A simple remote control holder that screws in or adhese to the underside of your coffee table. ...You can screw it using the pre made screw holes, or apply some double sided tape, like the ones 3M makes, to the small outcuts that are there to make it be...

simple Fire tv remote holder that has a groove on the backside for a large 3M Command Strip to adhere to the wall. ...I made mine with 20% infill but i Imagine you could probably get away with 0% infill if you have good bridging.

My AC Unit came with out remote holder and is always missing. ...So because of that and the fact that is kind of old and chunky y created a custom one Outer Measures: Height: 130mm Width: 50mm Depth: 27mm Inner Measures: Height: 50mm ...

A Sleek Remote Holder. Engineered Specifically for the Sony RM-ED035, Yet Versatile Enough to Accommodate Many Other Models as Well. Its Compact Dimensions Measure Approximately 53 x 19.8 x 31.3 Millimeters, Ensuring a Secure Fit in Any Setting. ...No...

this is my first design. ...i couldnt find a holder for my hdmi splitter remote so decided to make my own it fits nicely not too tight has a bit of slack for when you put screws in if you decide to mount with screws