3d printed atx case
2554285 3d models found related to 3d printed atx case.thingiverse
Follow the printer link (http://so3d.com.br/loja3d/impressora-3d-pro-gtmax3d-core-ab400/) *** 03/26/2018 Updated CASE MB with modern design, rounded on the front and with holes for LED HDD and POWER LED. Cover also updated with more modern air...
cgtrader
Simple case atx made from three side of glass, rear and structure made of aluminum , in the bottom there's space for PSU and HDD with 60mm FAN, in the center goes the motherboard with 80mm FAN, on top 120mm FAN
thingiverse
...... The whole mount to start off with is made from a flat motherboard by Atiesh; https://www.thingiverse.com/thing:3183250 The cabinet itself is of an old ATX tower. The full mount itself is made to be put in place of where an ATX motherboard would go.
thingiverse
A computer case that can use a Micro ATX motherboard.If your 3D printer can print 330mm*330mm area, you can print it happily!
thingiverse
Micro-ATX PC Case Made with Ender 3 v2 All structure 3D printed, with the exception of the side panels Structure made so that the front and side panels, slide on to place with no need for screws. In the Build front panel with vents. ... Side panels...
thingiverse
This is a ATX PC bench case with 2 fans radiator wather colling support.. ... Print from PLA and mont to 2 aluminium square tubes of 15x15x450mm.
thingiverse
final edition of atx board. ... down and top case now with corrected steps just printed at speed 40mm/S (or lest depends on the filament used) layer 0,2mm infill 15/25%
thingiverse
A simple case for an atx power supply. Hides all the extra wires while still letting it breath and stay cool. ... ** Be sure to flip the back plate over before printing, the underside has a large overhang ** This requires two #4 self tapping screws, or...
prusaprinters
ATX Power Supply Case Print instructionsThis is a simple model to print, but before you do check that back ports of your supply fit into holes and redesign if they dont. On the side there is a port for usb cable. ...I cut one old usb extension cable...
thingiverse
PiKVM case with ATX control board and OLED screen. Gerber file of ATX board is included. ... OLED screen: https://a.aliexpress.com/_9RsR8z Long screws: M2.5x30 OLED & CSI-bridge screws: 1.7x4 https://easyeda.com/al.pankov/zerow-kvm-v2
thingiverse
Micro ATX Horizontal Case compatible with Low Profile Graphics cards PC Componentes used: Motherboard Asus P5KPL-VM CPU E8400 3.0Ghz RAM 4G ddr2 800mhz SSD Kingstone 240G Graphics Card GT 710 1G GDDR5 TFX Power Supply Dimentions 360x270x110
thingiverse
Caja de ordenador al aire que encaja perfectamente con placas base ATX, Mini ATX y Micro ATX.
cults3d
Hi, Today's upload is a 3D printed PC Case, here is the specs: Supports up to ATX sized motherboards. Standard ATX power supply. GPU size up to 295mm 3x 120/140mm fans in the front, also support up to 420mm AIO. 2x 120/140mm fans on top or a...
grabcad
This is a 3D Printed Case for the BotBlox GigaBlox board.Kindly designed and contributed by Martin Pecka and his team at the Czech Technical University.
thingiverse
Replacement basic foot for desktop ATX tower case. ... To get the edges finished smoother so it doesn't snag on flooring or carpet I recommend putting this carefully in an electric drill (small part should fit 1/2" chuck) and file/sand the edges...
thingiverse
A 3D printed trashcan pc case. It has a the following hardware: 200mm fan in the top. The corners have been grinded away so it is round. 120mm aio in the bottom Corsair H60. ITX motherboard PCIE riser SFX powersupply Again please...
thingiverse
... Sorry I don't have digital designs for the aluminum plate with 4 "rivets" to stabilize the printbot simple maker. Print Settings Notes: 1/4 inch plywood printed with everything cut at 35% speed and 100% power on a full spectrum CO2 laser cutter
grabcad
This is a full ATX case made to hang on the wall, its made for my own pc specs. I haven't made the fans, motherboard, rams, psu, gpu or the ssd drives, these i've downloaded from this site just to make it look better. If that is not okey with the...
thingiverse
This is a simple case to convert a standard atx power supply to provide 6 outputs. I have used it as 5v, 2x 12v and 3x Ground but any configuration is possible even 3.3v. Knowledge in electrics is required and usually there is no need to open the...
thingiverse
This is a full ATX power supply cover, it was designed around a supply I had so you will need to check/edit the back cover to suit your own supply, I built it from scratch in Tinkercad but it's based on a few different designs I've seen on here so if...
grabcad
Project of designing of Micro ATX computer case was centered around the idea of a removable motherboard which allows for increased accessibility to the computer parts. This project had many changes through the entirety of the project it was very...
thingiverse
This is a simple case for a Duet Wifi powered by an ATX power supply. The power supply gets it's own chamber, with necessary power wires fed up to top chamber. Here there is a 120mm fan placed below the Duet mainboard for cooling. it slots into the...
grabcad
I'm making a mobius action cam case. It will be available at Shapeways.com asap. You can mount it directly on the damping pads. Fits the blackout mini h quad and the cheap Chinese qav 250. Other models available soon.
thingiverse
A power supply cover I designed around a DELL ATX power supply. To eliminate support material, I decided to make the top portion foldable. Holes fit standard Banana plugs. ... The top is attached with aluminum tape, that part could use improvement.
thingiverse
Having always been a fan of the design of the Apple G5 case and always having boring generic cases I wanted to make something unique inspired by the G5 case. There are quite some parts to this build, so don't think about printing this overnight. You...
grabcad
My design for a minimalist pc case made from brushed aluminium sheetmetal.
thingiverse
just a basic mini itx case, needs mesh on the top, front, bottom, and both panels which ever one you pick