3d printed dial indicator mount

================= [Av8er](https://www.thingiverse.com/Av8er)'s [Dial Indicator Mount](https://www.thingiverse.com/thing:3015709) unfortunately interferes with the X-axis motor housing of my Anycubic Mega Pro when left installed, and it would be...

Feeling frustrated, I made a beeline for Harbor Freight and picked up a Dial Indicator. However, I quickly realized that attaching it to the print head wouldn't be a cakewalk. That's when I decided to create this mount. It securely fastens to the DTI...

Dial Indicator (Reference Only)

This is a mounting block to solidly mount a dial indicator to any 2020 T-slot rail, but I adjusted the height so the indicator in the link below lines up with the table edge of a Creality Ender 3 V2. None of the bolt holes are threaded so you can use...

A Quick Design for a Dial Indicator Mount on Ender's X Carriage I came up with a fast design to attach my dial indicator to the back of the Ender's X carriage. Rear mounting was necessary because I run a bullseye and BLtouch in front, making it...

For mounting a dial indicator to the extruder head for precision bed leveling. How to use it: Step 1: Home the axis Step 2: Turn off the printer. You shouldn't move the extruder with the controls, as the dial will hit the tower before the extruder...

a semi permanent dial indicator mount for the Ender 3 Max. recommend running a tap into the smaller sized hole and running a short bolt through. A 1/4 20 x 1/2 to 3/4 inch long should be about right. ... there's still a little bit of flex to the...

Introducing the Creality CR-10's modified Dial Indicator Mount for stock CR-10 hotends, which fixes the issue of interference with cooling fan shrouds found in DIY3Dtech's original design. The redesigned mount fits perfectly on the CR-10's home...

I utilized Tinkercad to merge two of Ryan's designs, effectively creating a straightforward holder for my harbor Freight dial indicator that I employ to assist in leveling my MPCNC 525. I'm grateful to Ryan for designing and revising such an...

I couldn't find any mount that fit my particular fan duct setup (see [Ender 3/CR-10 FANG Lateral Cooler Remix](https://www.thingiverse.com/thing:3504842)), so I designed a custom mount for my dial indicator that snaps onto the stock 4010 hotend fan.

Dial Indicator Mount for V-Slot Profile. Designed to move the indicator in sync with XY motor GT2 Timing Pulleys, eliminating their vibration. For assembly, you'll need: - 1 x DIN912 M5x10 Screw - 1 x M5 Washer - 1 x Square M5 Nut or special...

This device attaches to your hot end housing to position a dial indicator, allowing for fast, precise, and effortless bed leveling.

============================================== Description: This holder is designed to slide a low-force plunger dial indicator smoothly along parallel printer rails. Specifically, the sled is designed to fit 2x 8mm rails, spaced 70mm apart - like...

... the Quick tool change (https://www.thingiverse.com/thing:3369444) installed on my machines. ... This Digital Dial Indicator is for that system. The Digital Dial Indicator I purchased was from Amazon.ca (https://www.amazon.ca/gp/product/B07C9MZ858/).

... the Quick tool change (https://www.thingiverse.com/thing:3369444) installed on my machines. ... This Digital Dial Indicator is for that system. The Digital Dial Indicator I purchased was from Amazon.ca (https://www.amazon.ca/gp/product/B07C9MZ858/).

... right. ...In response, I set out to craft a solution in Tinkercad, fashioning a tool designed specifically to align my print bed with precision. P.S. The dial indicator, sourced from Amazon for just $14, proved an invaluable addition to my toolkit.

This is a little mount I made for attaching a dial indicator to the print head of an Anet A8. its not perfect, but it works for me. The bore of the mount fits a gauge with a shaft diameter of about 8mm, and the little screw i use for clamping the...

The shank the dial's rod moves through, Can be mounted on the side or front.. Make sure it clears the X belt drive cover before homing with this mounted. If its too tight, heat it with a hair dryer and shove the indicator in. I didn't need to use...

This will enable you to temporarily attach a standard dial indicator (with mounting lug) onto a 52mm CNC spindle to assist in leveling the spoil board relative to the machine's XY axes. I used a 1/4 inch screw and nut to mount the gauge to the clamp,...

Install this dial indicator mount by sliding it under the upper hotend mount screws (may need to back them out a bit) and secure with two M3x8 bolts. Don't forget to snug up the upper two screws. Slide your dial indicator gauge in and tighten the...

Install this dial indicator mount by sliding it under the upper hotend mount screws (may need to back them out a bit) and secure with two M3x8 bolts. Don't forget to snug up the upper two screws. Slide your dial indicator gauge in and tighten the...

To fit an old dial indicator, I had to enlarge the cutout because it wouldn't slide into place otherwise. If you open this design in Tinkercad and ungroup the components, you can easily modify the opening to suit your needs. This new mount is wider...

I acquired a dial indicator from Bangood, so I had to modify the original design to accommodate a thicker diameter fitting. To make this easier for others, I'm providing a file that can be imported directly into Fusion360 and edited as needed if you...

I quickly devised a simple design to secure my dial indicator onto the back of Ender's X carriage. Mounting it at the rear was essential since I run a bullseye and BLtouch in front, making traditional mounting impractical. The design had to be easy...

I required to calibrate my build platform to a greater extent than the factory setting and had an old dial gauge on hand, so I created this device. It can be aligned to coincide with either the left or right extruder centerline. ...To install it,...

... ...For personalized specifications, adjust parameters such as offset (set to 5), bolt diameter (3mm), block width (25 units), mount depth (18 units), indicator sensor diameter (4.5mm), and indicator mount diameter (9.5mm).

This is a small attachment I designed to hold a dial indicator against the print head of my Anet A8. It's not ideal, but it functions for me. The hole in the attachment fits a gauge with an 8mm shaft diameter, and the tiny screw I use to secure the...

https://www.thingiverse.com/apps/customizer/run?thing_id=250957 Instructions Using the following options: Clamp length = 20 inches Lip depth = 5 millimeters Shaft outer diameter = 9.5 mm Hole border = 2 inches Clearance in clamp = 0.1 inch Build...

http://www.thingiverse.com/apps/customizer/run?thing_id=89243 Instructions Using the following settings: mount depth is set to eighteen units indicator mount diameter is nine point nine millimeters bolt diameter is three point six five millimeters...

The indicator is positioned directly under the nozzle, making it simple to access all areas of the bed. Neither the PINDA nor the hotend needs removal. Two M3x10 bolts secure the indicator from the back. ... Required parts: * 3 M3x16 cylinder head...