3d printed hermit crab shells

I encourage experimenting with springs and print settings if you know what you're doing to create a blaster fine-tuned to your needs. Grab your Snakethanhas here: https://www.thingiverse.com/thing:3890229 Feedback is very welcome, and though I...

Print Settings Printer Brand: LulzBot Printer: Mini Rafts: Yes Supports: Yes Resolution: .2 Infill: 20% Notes: If supports are not included, there may be some limited bone "matrix" inside the actual model; this might or might not be enough to...

It has nearly the same density as Earth, but smaller and uncompressed. This is because is has a comparatively bigger iron nucleus. Mercury is sometime consider the prototype of an iron planet, a planet composed mainly in iron. Its rotation is...

Deprecated: Please use newer V2. This is my attempt to design a mount for the Bondtech LGX extruder with the LGX FF for flexibles hotend kit. The extruder is mounted sideways attached to a mounting plate via two M3 side screws into the extruder...

Now have fun printing and installing the brackets. A little tip: Use heatsinks with thermally conductive adhesive and not with the adhesive pads. These are no good. If you like my design please show it with a like or a make here on Thingiverse. Die...

The switches are activated by two tabs mounted under the bed with M3 screws, nuts and the printed M3 T-nut converters (T-Nut-M3.stl) The upper Z-Axis switch is clamped to the Z-Stepper motor RHS mounting posts. The lowers mount just clips on. Make...

Of course, it requires a fairly high-resolution printer, 0.1mm or finer, to print these pieces successfully. With a gear train in place, I can now make a more robust small Pan & Tilt that will rotate up to 360 degrees or more. Required Hardware: ...

It's essential to print this component in HIPS or a similar material that's more heat-resistant than PLA. I've tested it with PLA, and while it works initially, it deforms and becomes brittle over time. Additionally, the cooling duct was designed for...

... Carl XVI Gustaf of Sweden presented Pink Floyd with the Polar Music Prize for their contribution to modern music. Thanks for checking in on us and for your ongoing support.CR8ED Out Of Hand Sculptor - Sandy Campbell3D Scanning and Printing - CR83D

One without Sling, (a selflocking design), but i redesigned it, because of the tolerances, while printing, the teeth are not as practical as I hoped. -GT2_Clamp_Ender_5_Y_Carriage_without-Sling_v2.stl (not recommended) So i created one, with a kind...

In Cura, you can place two models together and print them simultaneously by turning off Preferences -> General -> Automatically drop models to the build plate. This feature is essential for stacking the gears. Let's use our previous example to...

Print the nose with supports everywhere and 20% support density, also use 20% support density with support brim, support roof, and support towers enabled on the LID. Use four walls and 20% infill or more on the nose, and 40% on the LID - the lid...

For this team project i worked with Joanna Su (link) Problem Statement: With a partner, you will design a “2D” placard using Solidworks.  You and your partner will have the same design which meets the constraints below, and you will EACH use...

Edit 08/01 - Hey everyone, just as a heads up, this was designed to be the same size as the 'traditional' walker named after a type of battleship but after printing it myself I realize its a little bit bigger then I thought it would be. For...

Like my original version, this one is also designed to be printed easily without supports. However, I've found that a brim is necessary on my printer to prevent the small cable cap and wall between the cables and hotend from warping away from the...

Updates: 10/21/2020 : I have everything printed and working. I'm doing some testing and configuring. I'm currently working on the cable chain mount. <strong>Marlin settings</strong> X_PROBE_OFFSET_FROM_EXTRUDER 35.57 // X offset: -left ...

Includes an alternative top with a spot to mount a 30mmX30mmX8mm fan such as these: https://amazon.com/gp/product/B07QJ4MS2L Instructions I printed mine in PLA, 0.3mm layer height, no support. Files for two "Top" pieces are provided, the standard and...

De første undersøgelser har dog vist at stand-by-forbruget er det samme som med det forrige model.Køb af deleKontakt Bo Herrmannsen, hvis du er interesseret i at købe dele. Husk at sige at det er til STYRBAR-, og ikke...

The issue was that after a few prints, I had created a really cool "Rock". I wanted to be able to share the wonders of this illusion with the world, so I needed a way to present it. Did you know that "Necessity is the mother of education"? Armed...

MegaMAME is a large console which can be stood on a table, or you can use the stand to hook it over your knees while sitting on the couch :-) I had to split the case into two parts to be able to print it on my Ender 6. I'm happy about how it turned...

My old wooden LED bases are simple and elegant, but now I've created one that can be printed with ease. The distance between the LEDs is adjustable, controlled by turning the outer ring of the base. This allows for a customizable lighting experience...

so printed this idea first).So I love the idea of swords, and love the look of long swords, then i heard about hand and a half swords which are just long swords but longer, but not like stupidly big like double handed behemoths. This is a segmented...

... of the column. ‘Greetings,’ said the pale Blood Angel. His portcullis-faced Mark III helm was under his arm, leaving his face bare.” He doesn't have a bolter because I already had a Heresy-era bolter to use that I attached to the printed model.

Since my first-generation 2/3 plane connectors broke due to FDM layer separation issues, all the connectors in this series are printed so all connectors extend out on one plane, meaning that FDM printers are more than capable of building these very...

***PART #5*** https://www.thingiverse.com/thing:3379068 Are your printer full of dust and small filament pieces, well now it won' get stuck in the slots ***PART #6*** https://www.thingiverse.com/thing:3923876 Do you forget what direction to spin the...

The tiles were printed with natural PLA, and then welded with their bases using dichloromethane. They were washed and primed in black using Vallejo black primer through an airbrush. A watered mixture of a white craft paint, Vallejo Light Brown and...

http://www.thingiverse.com/apps/customizer/run?thing_id=53235 Instructions Using the following options: snapAxisSlack = 0.5 GENERATE_CASE = 1 baseFrequC0 = 17.4517 noteAlpha = 3 musicAxisHolderH = 2.4 crankDirection = 90 GENERATE_CRANK = 1...

I was inspired by the [Bed Cable Side Chain mod by Whoppingpochard posted at prusaprinters.org.](https://www.prusaprinters.org/prints/54320-artillery-sidewinder-x1-genius-illuminated-bed-cab) The mod relocates the bed heater and temperature sensor...

This format resembles a CSV-like list but seems to represent more structured data about design patterns and stencils for making printed circuit board (PCB) templates. The structure of the settings can be grouped as follows: ### Geometry and Stencil...

Replace the top thumbscrew to prevent inadvertent opening of the blaster.Print InstructionsBecause of the structural nature of the parts, I suggest using 5 or more walls and 25% or higher infill. No supports are necessary; place the rear of P1, the...