3d printed hypercube

I am not sure what print settings were done as I outsourced locally and can't find the transcript. So on that unfortunately I won't be able to help. The wiring is not the best solution but I am working on a breakout board to utilise just 1x...

I will post it in the files once I have printed and tested to make sure it meets my expectations! The following adjustments are being made: Larger base plate, more compact index to provide more angles, shortening the arms to not go beyond the base...

... convenience. Feel free to modify them however you please and post remixes for the community to benefit from! Print Settings: * Printer: Flash Forge Creator Pro * Rafts: No * Supports: Yes * Resolution: 0.200 microns for most parts * Infill: 40%

I would make the cable length to reach from your pants pocket to your goggles, or your shirt pocket, whichever works for you better. PS: If the LiPo buzzer is too loud stick two pieces of bubble gum into holes of little speakers, that will make the...

Print all the pieces with supports, with 3 or 4 bottom/top layers and 25% or so infill. The roller ends were made slightly too large. File them down evenly until the roller fits in the indents in the sides of the cartridge and spins freely. A little...

BEC set to 3.66V RMS --> VCC Hall sensor board pin 24 Jetson (physical pin == number printed on pcb) --> D0 Hall sensor board GND to GND This configuration is listed on Slack from @Doug and @Tawn (https://donkeycar.slack.com). Thanks to them! I use...

For this version print two large gears, both large and small shafts, one motor gear and the motor box. This add-on might fit on the other models this is based on like rmcht’s Double Gear Grinder and the Dual Drive system of claxly. There would be...

Tube (material doesn't matter, i chose stainless to match the optics of the bowl) some kind of epoxy glue assembly: after printing the required parts and buying the hardware you can start by assembling the scissor mechanism with the countersunk bolts...

eerything you need to play is included, it's an easy print for a game that you will play for days and days!!! hope you enjoy it!! Rules: in french sorry... (you can copy and translate!) Material list - 1 game box/stand - 1 game board - 4...

... or it can create a cone effect not allowing you to close the top. a little extra force may be required to pop the surround into the topBase. Commercial replication and production prohibited, selling files or prints without my consent is prohibited.

As of now, I am awaiting a new Creality hotend as well as the heated bed, and 165mm glass surface before printing can commence. However, movement systems work well. HARDWARE REQUIREMENTS Electronics: NEMA 17 Motor - replacement z-axis motor ...

Here are the dimensions for the eye module: * Length: 100mm * Width: 45mm * Height: 30mm All the parts were printed using ABS and then treated with an acetone vapor bath to give them a smooth finish. After the vapor bath, I drilled holes in all the...

i printed mine at 0.16mm layer height in PLA. Assembly Order:Before begining, test everything out of the case. You may need to cut the casing on the drive cables in order for them to fit 1. Attach Raspberry pi to Pi Mount: I used m3 screws for this,...

FYI, I am using an FDM printer for the base unit and anything that pops up through the pie panels I am printing in resin. Here is a video link of my electronics mock-up: https://www.youtube.com/watch?v=h6nXO9jEetk Base Unit Lower Limit...

You'll need to print three of my custom-made carriage blocks and three 10mm spacers. Don't use the blue carriage plate, as my new carriage block is integrated into it. Follow Shaunppl's instructions for installing linear rails on extrusions. His...

Instructions: Print in following order to avoid delays: 1) Left wall assembly To begin installing your Spaghetti Dispensing device first secure a piece labeled 'Left Wall.' Identify round portion from corresponding hopper elements, which should...

In the meantime I have developed this holder for 30x 1 Euro pieces so that you can just put the whole thing in the glove compartment and the coins do not roll wildly through the area.The distance of the coins is minimal from each other and the...

Depending on your print tolerances, you may find that you're unable to twist it that far. In that case, take the SCAR off the barrel, lock the sleeve so the barrel-gripping fingers extend into the inside, and file away some of the high points of the...

... but makes water available more slowly and requires a second catch basin. And as always, this design includes a public-domain dedication, free for use by all. Enjoy. If you print this and plan to utilize it, please let us know and show it off!

To achieve this, you can adjust your printer using the following template: https://www.thingiverse.com/thing:5413456 It allows you to adjust the feed rate specific to your filament to obtain precision of the order of a hundredth of a millimeter,...

My old wooden LED bases are simple and elegant, but now I've created one that can be printed with ease. The distance between the LEDs is adjustable, controlled by turning the outer ring of the base. This allows for a customizable lighting experience...

The mount model is positioned upside-down for printing without support. The interface between the mount and the clamp is a tapered wedge. This takes an instant to drop the Demel into, and it wedges tighter the more it's pressed down. Lifting the...

Print with supports, 3-4 shells, 10-15% infill (unless you want it to be dense). Post-Processing, I took a Dremel and cleaned out the grooves. I lightly sanded the front and back, to smooth out where the supports were. I then painted it, followed by...

... the 2 pole connector to the Einsy as they were too short for my box. The support of the two connectors is screwed to the frame in the 2 already existing holes. I printed everything with 0.2mm ABS. ...Filling 30% - 5 + 5 layers - 3 perimeters.

The interdisciplinary tasks allow in a simple and fast way a use in the classroom, such as mathematics, Language and general education, but also in the promotion of talent and afternoon care. Print Settings Printer Brand: Prusa Printer: I3 MK3S...

You will need these parts printed:1 Case (any variant, read below for info)1 Cover1 Angled Stand (any variant, read below)5 Potentiometer Cap (you can put a tiny piece of filament or a drop of paint in the small hole to make it easier to see how much...

THIS OBJECT IS COVERED BY CREATIVE COMMONS - ATTRIBUTION - NON-COMMERCIAL - SHARE-ALIKE LICENSE [CC BY-NC-SA] USERS CAN DOWNLOAD AND PRINT FOR PERSONAL USE, AND/OR DISTRIBUTE IF ACCOMPANIED BY APPROPRIATE CREDITS. <b>ANY USE OF THIS OBJECT FOR...

Includes an alternative top with a spot to mount a 30mmX30mmX8mm fan such as these: https://amazon.com/gp/product/B07QJ4MS2L Instructions I printed mine in PLA, 0.3mm layer height, no support. Files for two "Top" pieces are provided, the standard and...

I changed it because I didn't like the doors beeing in my way when using my printer from one side of my table.You don't need any clue the doors are held with small printed screws. I only have the screws at the bottom and it holds the whole door when...

I uploaded a photo of original thanks to reddit user lordwumpus.What you need:1 Old euro charger to salvage the 2 prongs/pins (cut them deep and adjust the height you need afterwards.)1 spring from a pen, preferably softer (cut in half)Hot glue gun 1...