3d printed razor handle

\nPrint Settings\nRafts: No big deal\n \n Supports: Unnecessary\n\n\n \n \n Directions\nHold steady while it prints. Slide the blade onto the handle until it reaches its stopping point. \nTroubleshooting:\nBlade won't fit? Check your flow rate and...

For folks with a stash of outdated safety razor blades, this tool is a godsend. ...The nut fits snugly over the top piece, securing the blade in place, while the cap clips down firmly onto the blade itself.\r\n\r\nIdeal for cleaning aquariums, its...

This handle uses M3 screws and nuts to screw together and clamp down on the blade for easier use.

------------------- The original version I like very much and fits well so far :-) However, with me the razor blade falls out again very easily, and for my used Bowden Tube Cutting Aid Tool by Maleh3Dprntx http://www.thingiverse.com/thing:3427170...

https://www.thingiverse.com/apps/customizer/run?thing_id=630237 Instructions Using the following settings: Bevel angle = 35 degrees, Slop = 1mm, Nut height = 4.5mm, Screw length = 12mm, Total length = 75mm, $fs = 0.5, $fa = 5, Handle diameter = 22mm,...

Manico per rasoio per testina filettata M4.Dopo la stampa 3d ho usata colla per incollare nella sede un inserto M4 in acciaio inox.ho utilizzato una testina di gillette mach3 ma può essere utilizzato per qualsiasi altra testina filettata.

I upgraded the handle of a fully 3D printed tripod from Thingiverse, now you can insert the legs into the tripod's handle.

... tool when not in use, while the Cover_FIX15mm.STL serves as a secure attachment point for the 3D printer frame. Print Settings: Printer: Minibot 120 Rafts: Yes Supports: Yes Resolution: 0.2mm Infill: 15% Notes: Sliced using Simplify 3D software.

Replacement X-Acto razor saw handle. ... Attach the razor saw blade and then secure it with a zip tie.

Remix of handle holder for Razor A5 Lux for M5 screw and nut.

These were useful for giving away a handle with a few spare blades.Hope this tool is helpful. Print orientationPrint the file with the default orientation. It should look like the image below. Plastic razor blades I usedI used orange plastic razor...

... tap, only to realize your normal tap handles can't hold it? ...Print this tap handle! The square hole securely holds a 2.7mm square tap, commonly seen on miniature taps. ...Use a sturdy plastic and 5 shells, so that the torque doesn't rip the plastic.

It's just a slimmer handle for HC razor with a cylinder that avoids the need of a threaded cap.

Revamped Emmett's razor blade handle design for smooth print removal on the build platform. The fit was optimized for commonly used single-edged razor blades like Stanley #9. To ensure a comfortable fit, the design features full cutaways under the...

... during use. The mechanical slide is like the one from Harry's: slide it towards the blade to remove the old and put on the new. Print this, throw it in your travel bag, and never be caught without a handle. ... READ ALL THE INSTRUCTIONS, please.

But 3-4 of their handles broke before I ran out of blades, and the 3D printed handle did not do any better. Their handle design is just bad. I transitioned to Harry’s after I compared the shave of Harry’s to Dorco and Gillette on half my face for...

Razor blade handle with case for hide blade and store spare razor blades.For attachment top handle cover - metric screw: 2x - M2 and 1x M3 or tie a twine.Excellent for cutting to fruits, vegetable and decorating homemade bread.

This is a convenient handle designed specifically for single-edge razor blades. The provided plans are right-handed oriented, but they can easily be mirrored to accommodate left-hand users. Three variations of the STL file are available - (A)...

Razor blade holder with storage case perfect for storing hide-out blades and spare razors. For adding top handle cover attachment - use metric screws: two x M2 and one x M3 or secure it with a twine. ... Ideal for slicing fresh fruits, chopping...

... thumb and index finger for pushing and pulling along the stone. Please post your makes. EnjoyUPDATE: 1.20.24Added file "Kampfe_Star_Razor_blade_honing_handle.stl"The shaft on this handle matches the spine of the Kampfe Wedge blades and others.

... let model material populate the blade insert!!It takes FOREVER to eat that stuff away in the acid bath. Just use support from the base to the part. Print it oriented as-is and you'll be fine.Hope you find it useful.Category: 3D Printer Accessories

This is a remix of the EZ-Snap Razor Blade Handle by AdanA, adapted for classic double-edged (Gillette) safety razor blades that are only 0.1mm thick and prone to slipping under prints easily. You won't be able to lift any prints with such a blade...

(I kept v2 available for those who prefer the extra bit of flexibility in the razor blade.) I recommend printing this at 0.1mm layer height to ensure that the subtle recess that prevents the blade from moving around, comes out right, and the tab to...

I lost by beloved Harry's Razor, and had lots of the blades I could no longer use without buying a new one, so I designed my own. It's not perfect but does the Job. Printed on My Ender 3 Pro. ... Print with adhesion 100% infill or Gradient infill....

... significantly reduced from its original size, and then reinforced with a sturdy bar. ... Print Settings Printer: M3D Micro Rafts: Yes Supports: No Resolution: It makes no difference what the resolution is. ... Infill: A medium infill density is chosen.

I use this tool extensively for my 3D printer prep and cleanup. ... Print Settings Printer Brand: Prusa Printer: Prusa Steel Rafts: None Supports: None Resolution: 0.18mm Infill: 30% density

Instructions Using the following options: Knurl Smoothing: Increased to Maximize Durability Screw Clearance Diameter: Scaled Down for Tighter Fits Overall Length: Configured for Extended Reach and Stability Bevel Distance: Set at Optimal Angle for...

... ...Using these parameters: nut_flats_diameter = 9 bevel_angle = 50 transition_dome_scale = 9 bevel_distance = 3 handle_diameter = 16 screw_clearance_diameter = 6 screw_length = 10 knurl_smoothing = 65 overall_length = 90 transition_length = 15

I fell in love with Guntars' original handle design, but unfortunately it was too big for my smaller printer. So, I took matters into my own hands and created a shorter version that still captures the essence of the original! Same sleek design, just...

http://www.thingiverse.com/apps/customizer/run?thing_id=630237 Instructions Using the following options: overall_length = 85 transition_length = 10 screw_length = 15 knurl_smoothing = 75 transition_dome_scale = 2.5 bevel_distance = 2...