3d printed simple dimple
2560387 3d models found related to 3d printed simple dimple.grabcad
... 40x8mm dimples in 2mm AW-5754 aluminium. ...(Amada V40 die included)I use a 4mm guide pin in between the die adapter and bottom dimple part to keep them aligned. ...You could easily just modify the geometry to get the same result without the guide pin.
cgtrader
Simple Dimple (or Simpl Dimpl) is a silicone toy with several convex-concave parts. ...The anti-stress effect is achieved by repeatedly pressing these dimples.
thingiverse
"Simple 3D Printed Rocket Nosecone.stl" is the nosecone "Simple 3D Printed Rocket Airframe.stl" is the airframe! This rocket is not saleable as it is designed so the motor can slide in through the bottom, and if that size is changed, your rocket...
prusaprinters
A simple 3D printed succulewnt planter. It prints in 2 parts and the top pieces has a drainage hole into the bottom piece. Print instructionsI printed this at a 0.3mm layer hieght on my Prusa MK3S. ...THe bottom part took about 2 hours and the top part...
myminifactory
A simple 3D printed succulent planter. It prints in 2 parts and the top pieces has a drainage hole into the bottom piece. I printed this at a 0.3mm layer height on my Prusa MK3S. ...THe bottom part took about 2 hours and the top part took about 3.5...
prusaprinters
I've made this simple online customizer (https://www.sol75.com/component/glider_if) where you can easily change the main parameters and then download the modified STL. The frame is quick to print (a bit more than 1 hr, depending on the...
prusaprinters
Inspired by the designs of the Japanese design firm Nendo we made this so we could have some on our desks. This print can be done either in a single material or with an MMU Print instructionsIf you are using the .stl file you will need to split it...
cults3d
Simple 3D Printed RC Airboat for Graupner Vector Unit Extreme https://youtu.be/Eu6CRpB3wq4 Control Unit and Power Pack: Vector Unit Extreme, 3 in 1 Motor Set https://www.graupner.com/Vector-Unit-Extreme-3-in-1-Motor-Set/34003/
thingiverse
Simple 3D Printed RC Airboat for Graupner Vector Unit Extreme https://youtu.be/Eu6CRpB3wq4 Control Unit and Power Pack: Vector Unit Extreme, 3 in 1 Motor Set https://www.graupner.com/Vector-Unit-Extreme-3-in-1-Motor-Set/34003/
prusaprinters
Simple 3D Printed RC Airboat for Graupner Vector Unit Extreme Control Unit and Power Pack: Vector Unit Extreme, 3 in 1 Motor Set Print instructionsPrinter Brand: Prusa Printer: Prusa Mk1 Rafts: No Supports: No Resolution: 0.2 Infill: notes...
myminifactory
I made a very simple 3D printed clock driven with an Arduino board and a stepper motor.I had two ideas in mind with this clock: - Make a real simple clock, no other hardware needed (other than the electronics).- Show how IT can interact and improve...
prusaprinters
One is for a single layer of coins and the seconds one is capable of holding two layers of coins.Banknotes can be held between the outer shell and the elastic band.PrintingPrinting one plain side and one with the engraved text gives it some nice...
thingiverse
This is a 3d printed model rocket that fits 18 mm solid rocket motors. I've used it with c class motors. When you build the rocket, glue the long tube onto the fincan. Then glue the small square piece with the hole onto the bottom of the nosecone.
grabcad
the frame need to have a ledge at the back, and shouldn't be too high (25cm maximum) but can be pretty wide takes 15h on an ultimaker² and if you use another printer, make the print slower than normal because it is a pretty high print with not much...
thingiverse
A quick and simple desk stand for the awesome 3D Printed Watch with Tourbillon
thingiverse
... simply arrange your drawers with dividers to keep them organized! Full instructions on Instructables: https://www.instructables.com/Simple-Drawer-Dividers-With-3D-Printed-Connectors/ Or for Sale on Etsy: https://www.etsy.com/shop/TaylorMadeCustom3D
thingiverse
A simple 3d printed claw that I designed to be used with a 9g servo. It keeps the servo parallel to te claw action in order to reduce the weight in the arm. ... https://www.youtube.com/watch?v=FNFmIbqV8nc
thingiverse
... a table without falling off! -Check out the Instructable for complete instructions!http://www.instructables.com/id/Simple-3D-Printed-Arduino-Robot/ Print Settings Printer Brand: Printrbot Printer: Simple Black Rafts: Doesn't Matter Supports: No
myminifactory
After a long afternoon of design, 3D printing and assembly, "A Simple 3D Printed "Walking" Mechanism." was the result. And as indicated in his video, the mechanism indeed powers over "rough" terrain with ease. My implementation of his design...
cults3d
After a long afternoon of design, 3D printing and assembly, "A Simple 3D Printed "Walking" Mechanism." was the result. And as indicated in his video, the mechanism indeed powers over "rough" terrain with ease. My implementation of his design...
thingiverse
This is a 3d printed storage system that is great for a desk , kids desk, sewing room, den, garage, shop, etc. Simple design print a tray and a drawer and the pins for the corner times 4 of course. Made so can be 4 tall (at max for pin size as on...
thingiverse
It's 3D printed part that allows the robot to be left up to tests can run.
prusaprinters
https://www.etsy.com/shop/StoneysMakerPlace?ref=l2-about-shopname Feel free to drop in or if you have a project for the home that needs some out of the box thinking I'd be glad to offer a hand and estimate. Here is my Etsy Page:...
cults3d
There are 8 unique 3D printed pieces (10 total) that create the frog, all pieces print without support and, for me at least, required no filing, sanding or other clean up prior to assembly. ... Designed using Autodesk Fusion 360, sliced using Ultimaker...
myminifactory
There are 8 unique 3D printed pieces (10 total) that create the frog, all pieces print without support and, for me at least, required no filing, sanding or other clean up prior to assembly. ... Designed using Autodesk Fusion 360, sliced using Ultimaker...
thingiverse
Simple wingholder holds the wing to prevent it sliding down while in upper position
thingiverse
All that is needed to complete one half the landing gear is the 3d printed parts with 3 pieces of 4mm carbon fibre that is 118mm, 100mm and 125mm long and a piece of m4 threaded rod to fit the shock on. ...I put a piece of 5mm balsa inside the fuselage,...
thingiverse
Attached files are: A picture of the bridge in the testing rig A picture of the bridge with the heaviest load born before breaking A picture of all members fresh off the printer a picture of the members being weighed An STL for each individual...