3d printed throttle quadrant

The throttle quadrant perfectly complements the saitek pro flight system, fitting it like a glove. Two start levers are prominently displayed at the front of the device, and the box itself holds the quadrant at a 45-degree angle. ... Video...

Flaps design for Saitek throttle quadrant. Three parts to print.  When printing you need to make sure that the bottom hole of the smallest object is 54x104mm, and scale the other objects as well. The smallest part and the part with the hat has...

This is a small throttle quadrant for two-engine prop planes. It features throttle-, prop- and mixture-leavers. My goal was to keep the design simple with focus on functionality and to get this into a smaller form-factor. It uses an Arduino Pro...

The throttle lever has been expertly designed in the likeness of a Dash 8's control stick, specifically tailored for use with the Saitek Pro Quadrant. ...To ensure a rock-solid installation, I've carefully separated the lever base, allowing you to...

I'm Sharing the Flap Lever for Saitek Throttle Quadrant. If you're interested, I can sell it as a complete set. You can reach me more easily through my email. ... Gmail : sindemirci.96@gmail.com My designs are available at:...

This adapter turns the Saitek Throttle Quadrant an impressive 45 degrees upwards, significantly enhancing my overall comfort while flying. I find it allows me to fly with greater realism and authenticity, especially when simulating aircraft types...

These slide-on covers quickly change your CH Throttle Quadrant from multi-engine mode to single engine mode. A precise fit over the existing throttle, prop and mixture knobs. The covers have a small detent that keeps them centered in place, no...

Cheap and simple 3D printed throttle quadrant Assembled units can be ordered here: USA here: https://3dparts.biz/CAN here: https://home3dcockpit.com/   This unit has no joystick board, but can be connected to any DIY unit you already have. Or simply...

Improved large levers and switch addons for the Saitek Throttle Quadrant. Inspired by Diamond DA62. Print the levers twice for Twin Engine, Small Lever can be used for brake or speedbrake. Switch addons (for flaps, gear, misc) can be fixed with...

Chunky throttle handles for the Honeycomb Bravo Throttle Quadrant. **UPDATE**: April 2 '21 - The left hand skewed offset handle had a modeling error that I never detected. I also never test printed it originally, but have since tried the area of...

These should fit somewhat snugly down over the throttle levers, similar to the interchangeable grips that are included with the throttle quadrant. They also raise the grip level so that the throttle grips are significantly higher, so if you're only...

Added a quick-change connector to the levers of brettkp's Throttle Quadrant. Goal is to make it easy to switch the quadrant to match controls of different types of planes, e.g. a modern single engine turboprop (example provided) to a twin engine, to...

I am making available here my A320 completelyThrottle attachment for theLogitech G Saitek Pro Flight Throttle Quadrant.The throttle has no function, just an optic for a better flight feeling.Airbus A310/319/320/321/330/350

They slide onto the levers just like the interchangeable grips that come with the throttle quadrant, but extend upward significantly, increasing throw on the throttles and raising them up out of the way of the third lever. I personally use these...

I am designing a throttle lever based on the Airbus A320 throttle quadrant, specifically for the Saitek Pro Flight Throttle Quadrant. My concept focuses solely on one slider for both engines, as it's intended to be a fun project. The lever is...

I am making available here my A320 Throttle attachment for theLogitech G Saitek Pro Flight Throttle Quadrant.The throttle has no function, just an optic for a better flight feeling.ENG I and ENG II fit perfectly, so the middle slot can be removeOf...

Mixture Knob unchanged from Stephen's design Prop Knob modified angle/sleeve location to sit a little higher Throttle Knob and Extension modified for longer extension, different knob Some supports needed. Use your best judgement (I only used...

Mixture Knob unchanged from Stephen's design Prop Knob modified angle/sleeve location to sit a little higher Throttle Knob and Extension modified for longer extension, different knob Some supports needed. Use your best judgement (I only used...

I design this project to create a throttle quadrant for PC simulators and RC FPV, inspired by the SIMCHAIR III on Thingiverse. Some parts are borrowed from JonahTsai's F16 GitHub repository. Parts that connect these components are laser-cut in...

After printing, you should glue the arduino to the roof of the case (if yo used Leonardo, print this https://www.thingiverse.com/thing:39990 then glue the arduino to this case and this case into the Throttle case, and it will be seen as in the...

I am making available here my A320 Throttle attachment for the Logitech G Saitek Pro Flight Throttle Quadrant. The throttle has no function, just an optic for a better flight feeling. ENG I and ENG II fit perfectly, so the third slot can be used ...

... You do not really need any specific settings for this print, if I was nit-picky, I would probable recommend to decrease the elephant's foot and decrease layer height of the lower most part so the knob is well rounded, but it is not necessary at all.

This gives you a better fit on the throttle levers and a longer throw on the throttle. You may need to sand down the top end of the lever slightly, but the fit should be very snug, no glue necessary if you do it right. Printed with PLA, 10%...

This is an improved set of jet fighter-style throttles for the Logitech/Saitek throttle quadrant. ... The grips are my own design, the included lever is remixed from Opteryx's Bf-109 throttle lever (the original lever works too if you want a longer...

The throttle quadrant is a perfect fit for the Saitek Pro Flight Throttle system, its precise dimensions guaranteeing a snug and secure connection. ...Two prominent start levers sit proudly at the front of the unit, while the quadrant itself is cleverly...

### 3D Model You can see assembled 3D model in [this URL](https://a360.co/2Yg0hqr) (password is Throttle) Also see [5-way Hat/POV Switch housing](https://www.thingiverse.com/thing:4934310) and [Frame for Push Button 6x6...

If you build the full version of the throttle quadrant and trim wheel of Zefram, you can use this part to cover the electronics. You have to drill 4 holes on the back side of the throttle quadrant. You have to drill out the holes for the screws in...

nicht ganz perfekt aber ein wenig feeling kommt damit schon auf. ...Viel Spaß

This design was formed in November, utilizing SolidWorks 2010 software for its creation. ...The visual presentation of the model was achieved through the utilization of SolidWorks Photo View 360.

Idea from srbarlow3 made it so you need less Ramps