3d printing part cooling fan

Printer arrived without a part cooling fan. Repurposed Walter's Fan Mount (RigidBot) fan mount to fit Core i3. Then utilized the duct from lobocnc's MakerGear M2 blower duct. You could also try using other ducts, such as those found at...

... for the Titan Aero with a volcano hotend. ...Print with platform supports only! The holder is for the Titan Aero with pancake stepper. One version is for the use with a heatsink. Fusion 360 model: http://a360.co/2Btdon1 Category: 3D Printer Parts

Additionally, I'd been using a popular ring duct, but as it's only supported by the fan attachment bolts, it sagged over time due to heat from the nozzle until it hit the print. This remix fixes several problems with the original design and improves...

Finally, add these lines to the very end of your custom end G-code: M42 P11 S255 M190 R25 M42 P11 S0 M140 S0 With this setup, the cooling device will start automatically at the end of each printing and continue until the hotbed has cooled down to...

assembly is pretty simple, remove your stock hot end fan and part cooling fan, bolt the new hot end fan in place with the same stock screws and use the clip on the other side to secure it to the gantry, use a Zip Tie to secure it in place along with...

I designed a new part cooling duct specifically for use with a 40x40x20mm 12V Noctua fan during my project of silencing the printer. To ensure optimal airflow, I crafted the channels to allow for smooth flow and concentrated the airflow directly at...

Externer Teilekühler, 4x 80mm Lüfter.ich habe Arctic P8 MAX verbaut und bin sehr zufrieden.die Nachteile des einseitigen abkühlens werden hiermit umgangen.external parts cooler, 4x 80mm fans.I installed Arctic P8 MAX and am very satisfied.This avoids...

Phelanp11's Mosquito Hotend mount is compatible with Creality CR-10/Ender 3 printers and also works seamlessly on Ender 5 models, but unfortunately, the part cooling fan cowl he designed does not fit perfectly. ...To resolve this issue, a revised...

I created a duct piece for installing the cooling fan, by attaching the hotend mount section, and made it functional as before. ...The design now includes a sufficient airflow area and precise spacing to ensure no contact with the stationary build plate...

* 5015 Part Cooling Fan * Pancake Stepper Motor * Normal Nema 17 Stepper Motor (compatible only if the EzABL portion of the mount is not needed) This updated design incorporates several new features. I added an EzABL mount, part cooler, and slightly...

I tried several models of ducts I found here on Thingiverse, but it would appear that my part cooling fan has a larger opening than any of the models I found here, because none of them fit. That said, This model that I made from measurements of the...

A custom mount combines an E3D v6 hotend, a BLTouch probe, and a 40mm part cooling fan to optimize print quality.\r\n\r\nInspired by previous designs, this creation offers a unique solution for those seeking improved performance.\r\n\r\nNote: This...

this is a simple remix of the Hangtight part cooling fan shroud set up for the Voxelab Aquila. a gentleman names Gene Givens on the official Voxelab FB page created this but only ever loaded it to google drive where the files got lost. files have...

Airflow goes straight to the nozzle tip where it belongs.Print sideways as shown in the screenshot.Print in ABS/ASA or PETG.Reuse all original screws to secure the mount plate to the extruder and the fan to the mount.Will need 4 M2 nuts. ... Pressure...

... for the Titan Aero with a volcano hotend. ...Print with platform supports only! The holder is for the Titan Aero with pancake stepper. One version is for the use with a heatsink. Fusion 360 model: http://a360.co/2Btdon1 Category: 3D Printer Parts

It uses three 40mm fans, the two outermost ones connected together to cool off the extruded plastic, and the center one to cool the cold side heatsink. It mounts with four m3x10mm screws to the heatsink, and the fans all mount with m3 up to 30mm...

However, I wanted to revisit the part cooling situation and add a 5015 blower fan, as I was getting a lot of air blowing back through the 4010 fan on the original design. The part that I've made for this is "5015 Anycubic Kossel Effector" which is...

This is a mix of the Prusa Mk3 style part cooling fan duct, I have added the BLtouch mount to it. there are two variants v2 has the BLtouch mount as far back as it will go and was the case when using the BLtouch mount separately. ... V3 has the mount...

I added that file as an option (the differences are moving the mounting hole up 1mm and shaving 1-2mm off the rib in the middle where the fan duct connects to the fan). Note: I use a non-standard nozzle that's a tiny bit taller than the standard...

I added an airduct for 40x40x10mm or 40x40x20mm silent noctua fans on the right side for part cooling. All mounting holes are diameter 3,8mm for threaded M3 inserts. There is a version with a box cutout on top for step down converters. The left...

This design is specifically tailored for the 2017 "New effector" model, utilizing a powerful 4020 centrifugal blower...

I was let down by the standard Prusa cooling fan duct because it obstructed my view of the nozzle, yet performed well overall. I sought a straightforward, compact, bolt-on replacement that wouldn't require relocating the fan, drilling holes, or...

(Foto) Don't forget to insert the M3ns nut in the slot (for the noctua fan screw) Prints without support when printed in mounting position. All other details remain and can be read in the original post of jonathanrswift who deserves all the honor...

This duct is a blast to use with a 40mm fan that's specifically designed to chill out both the heat break and printed parts. ...It securely attaches to the front of a standard Wade's geared extruder body.

It employs three 40mm fans, with the two outermost ones linked together to chill the extruded plastic, and the center one focused on cooling the cold side heatsink. The design attaches securely using four M3x10mm screws to the heatsink, while all...

I've tweaked xile6's original 30mm print cooling fan design with a second cooling fan installed directly next to the hotend nozzle. As originally envisioned, the side ducts remain carefully offset from the nozzle to ensure efficient heat dissipation...

After a few iterations, here is the first working version of my big fan part cooling system. Im not good at naming things, so I will call it "Yeti" for now. Fan specs: 140x140x25 mm 24V ------ Update 25/01/2022 Deleted the v1 files since they don't...

This fan duct lets you get parts cooling going with an Ender 3 setup for non-planar printing, just like Teaching Tech shows in their YouTube tutorial https://www.youtube.com/watch?v=gmePlcU0TRw https://imgur.com/a/oPbYXSV first pic is in proportion I...

https://www.thingiverse.com/thing:6250296 Simple add on mount using one screw of bottom of heat sink fan, leaving clear line of site to nozzle and ability to clear nozzle debris during printing. Leaving unobstructed airflow to both adjacent sides for...

The stock Fan duct is so bad I needed to design a better one that cooles the material everywhere and not from just one side. So, I designed one. Feel free to modify to your needs. ...A duct for a 40mm fan is planned and will follow.