3d printing part cooling fan

Remixed the holder for 20mm high fan.

i designed 2 fan duct to be installed on smart effector using 4020 fans

Just slightly modified fan duct. ...they are tapered, to deflect air in direction of a nozzle. It is improvement over a stock duct, but still some limitations because of steel frame in a way for more direct duct. Category: 3D Printer Accessories

*Use the excact .3mf file has been uploaded to print this case to obtain a perfect air duct surface.(the support has been set, Please do not change the sliced file)*Printed in ABS (or other materials with good heat resistance, Do not use PETG to...

This is a remix of Motogeepie's wonderful fan duct, I only combined the two parts to one. Thingiverse servers have reached the end of thingiverse and won't let me tag the original thing, so here's the link:...

For geeetech A20M with a 4020 radial fan. ...

Mount for 15 x 20 mm Duct style fan.

You're going to require a 4010 fan immediately.

Spade - Infil to add weight, no supports Letters - Print flat, already scaled to fit nicely in the embossing Star - Infil to add weight. Full print with 4x4x4 walls/top/bottom and 38% infil came to about 48g in weight. Glue in lettering and...

It has been designed for 4015 radial fan and stock fan shroud of ANET ET series. ...You need 2 M2*20 screws.

... using a drill or file for a perfect fit. The recommended print settings include utilizing a heat-resistant material like PETG, and you'll want to set your nozzle size to 0.4mm, coupled with a 0.2 layer height for optimal results. ...Happy printing!

5015 fan support for a standard hevort printhead with a e3d v6 hotend. ...

flip it so it prints standing up with a couple of supports at the nozzle tip to help it print. Mirror image it so it can be used on the right extruder. SO as to avoid it contacted the fan blades. It fits both F430 and F160. You may wish to...

......This modification allowed me to sit the fan mount higher up on my hotend, which was a key goal for me. The fan still fits snugly into its new home, giving me the reassurance of a secure connection rather than a loose fit around the output of the fan.

... fan duct design is suitable for the stock hot-end and others of a similar size. However, I created an alternative volcano fan duct design specifically for hot-ends that hang lower than the stock model - perfect for E3D's Volcano hot-end setup.

The system requires a modification to item 2608078 and also needs an update to the fan duct by December 29th, 2018.

I created fan duct for my custom printer. Feel free to customize it for your one or just have idea how to make it. ... No supports 0.25

However, it still works with just one bolt.\r\n\r\nThe fan itself, featuring red and black wires, simply needs to be connected to the "FAN" port on the Melzi board. ...With slicer settings from the firmware, it starts working right away.\r\n\r\nBEWARE -...

This secures the blower fan directly to the Tevo Tarantula x carriage assembly. Remove one of the top front bolts holding the hot end in place, then mount this diagonal bolt using a longer M3 screw. ...The fan is secured with an M4 bolt and nut into its...

... a Dragonfly extruder that is not as long as the stock hotend on the SV01/SV03. ... Update: the small size results in very poor air flow. Instead, use either the original or my BL Touch remix of the fan housing to allow for using a regular fan shroud.

I needed a quick replacement fan as my blower went out, and all I had access to that would accept 24v was a 6020. It works well enough, even if its a bit big. One thing to note, the holes for mounting the fan arent aligned very well. You could...

I built this nozzle with two main goals in mind: it needed to be a replacement for the warped one that came with my 3D printer, and it had to improve airflow and direct the air stream more effectively towards the nozzle tip. ...The design focuses on...

I have left the single-part version intact for reference but have also included a new two-piece print, comprising an upper plate that clamps onto the extruder's plate and a lower section that features a refined airflow channel; securing the assembly...

This is the ninth version of my component fan construction. I use a slightly modified version of Banholm's magnetic X-Carriage (https://www.thingiverse.com/thing:1829779). However, it should still be compatible with Banholm's design if you use the...

They've tweaked the fan duct design, giving it a subtle taper that directs airflow straight into the nozzle. ...It's an upgrade from the standard issue duct, but its steel frame still hinders its potential for a more streamlined path.

... ... Layer height: 0.12mm Manual Support - Bridging is Possible, No Support Inside; Only Fan Inlet! Fits Perfectly to My Sovol Printer. Edit 27.01.20: I've Made Major Changes to the Air Duct, Making It Larger and Significantly Improving Air Volume.

I designed and manufactured this part specifically to enhance airflow with a Creality Ender 3 printer, utilizing a high-quality Fillamentum ASA Extrafill filament that boasts superior heat resistance compared to standard PLA material.

Inspired by other parts out there that don't fit my printer exactly. The duct sits comfortably around the extruder, with a around 1mm gap above and 1mm distance from the tip of the extruder. ...Does not seem to be affected by the heat at the given...

Simple little fanduct for use with 8mm M3 screws, prints without supports. ...Also, thanks to Rudolf Huttary for writing this awesome time saving lib sc.scad.

I wanted a more uniform airflow around the print head. This took a couple prototypes to complete but works amazing. ...Uses the original bolts and nuts.